Unofficial magicJack Forum

Unofficial magicJack Forum

Your Unofficial magicJack and magicJack Plus phone service information resource
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
Tomato Version of MJMD5 (aka mjproxy)
Goto page 1, 2  Next
 
Post new topic   Reply to topic    Unofficial magicJack Forum -> magicJack Tips, Tricks, and Hacks
View previous topic :: View next topic  
Author Message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Fri Jul 17, 2009 12:19 pm    Post subject: Tomato Version of MJMD5 (aka mjproxy)

Now that I've got MJMD5 working on my Tomato flashed Linksys WRT54GL router, I thought I'd consolidate all of the information I found in this forum and from PMs to help other newb's.

Thanks to jeffnyc, qwer1304, and Taken83oveR's post on the following thread for guiding me- http://www.phoneservicesupport.com/ddwrt-version-of-mjmd5-t6913.html

Since I was totally new to this, it took me about 6 hours to figure everything out. The biggest hurdle being I am not familiar with linux commands that were available once telneted to my router. The following link lists all commands available for Busy Box which is what my router uses and is an excellent resource - http://en.wikipedia.org/wiki/BusyBox


Summary of steps that need to be completed:
1. Enable jffs in Tomato via the Administration section
2. Enable ssh in Tomato via the Administration section
3. Install putty on PC (download the 'Windows installer for everything except PuTTYtel' version)
4. Download the Tomato version of mjproxy from teddy_b's post
5. Upload mjproxy to Tomato (jffs) with putty using Windows command prompt with -scp option
6. Telnet into your router via putty (login as 'root' and enter Tomato password)
7. Execute the following command while connected to your router via putty - 'Chmod mjproxy to 755'
8. Put command line in Tomato Administration/Scripts/Init tab
9. Change the proxy IP in your ATA Line 1 tab to that of your Tomato router
10. Verify that mjproxy is working using the top command


Detailed instructions with screenshots below:

1. Enable jffs in Tomato via the Administration section
I also clicked the 'Format/Erase' button so that I have a clean slate to work with.
I wasn't worried about deleting anything since I just enabled it.


2. Enable ssh in Tomato via the Administration section


3. Install putty on PC (download the 'Windows installer for everything except PuTTYtel' version)
Link to PuTTY download page-
http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html


4. Download the Tomato version of mjproxy from teddy_b's post
Extract mjproxy to Program Files/Putty folder.
NOTE: I needed to unzip the file twice.
teddy_b wrote:
I don't have a DD-WRT router either, but here are a couple binaries compiled using Tomato toolchain.
1. The first one is what I'm running on my Tomato router:
http://www.mediafire.com/file/twkmijnm3mz/mjproxy-tomato.tar.gz
It might work on DD-WRT - I have no way to check myself.
2. If the 1st one doesn't work, try the other one:
http://www.mediafire.com/file/n2zzlmkiyyv/mjproxy-tomato-static.tar.gz
This one is statically linked with uclibc - the executable is larger but doesn't depend on the libc version - has better chances to run on dd-wrt (only on mipsel routers of course).


5. Upload mjproxy to Tomato (jffs) with putty using Windows command prompt with -scp option
Open a Windows command window (via Start/Run/Cmd) and navigate to the putty directory. Notice in the screenshot below I executed the command from the following directory- C:\Program Files\PuTTY
Then type in the following command-
"pscp -scp mjproxy [email protected]:/jffs" (assuming 192.168.1.1 is your router IP)


6. Telnet into your router via putty (login as 'root' and enter Tomato password)
Open putty and enter the IP address of your Tomato router in the 'Host Name' textbox and then click open


A telnet session window is created and log in as root and enter your Tomato password when prompted
(Note: when you enter your password the cursor doesn't move)


7. Execute the following command while connected to your router via putty - 'chmod mjproxy to 755'
In my screenshot below I first looked for mjproxy to verify that I successfully uploaded it.
After I executed the chmod command I noticed that mjproxy changed to a green color.

For those not familiar with linux- I used the following commands to look for mjproxy
pwd = present working directory
ls = list files in this directory
cd = change directory


8. Put the following command line in the Tomato Administration/Scripts/Init tab
sleep 30
/jffs/mjproxy 0.0.0.0 5070 proxy01.chicago.talk4free.com 5070 your_MJ_password


9. Change the proxy IP in your ATA Line 1 tab to that of your Tomato router
I also enabled NAT Keepalive because I was having issues with incoming calls.


10. Verify that mjproxy is working by using the 'top' command while connected to your router via putty. (Type ctrl-c to stop the top command)
This was really helpful for me in debugging because it turned out that mjproxy wasn't running on my router so I had to manually execute mjproxy.

Just enter 'top' at the telnet command prompt and ctrl-c to stop.

If mjproxy is running you should see a line similar to the one below in yellow-



That should be all to it. Log into your ATA and confirm that your registration status is 'Online'. One thing I did notice is that it took about 3-5 minutes before my ATA registration status changed to 'Online' after manualy executing the mjproxy command.
Back to top
View user's profile Send private message
tdave00
magicJack Apprentice


Joined: 11 Jun 2009
Posts: 10

PostPosted: Sat Jul 18, 2009 3:54 pm    Post subject:

Very good detailed writeup. Had another user PM me asking how I did it and my instructions to him were a bit vague. Glad you took the time to do it in detail. Been working fine for me for almost a week.
Back to top
View user's profile Send private message
nakamoniel
MagicJack Newbie


Joined: 29 Dec 2008
Posts: 9

PostPosted: Wed Jul 29, 2009 9:51 am    Post subject: MANNYYYYYY THANKSSSSS

Oki, this is the perfact guide i have came across ever. For some reason with DD-wrt even after enabling JFFS2, I was unable to put mjproxy file in there. That made me switch to TOMATO and now i Absolutely love it. I am not familiar with linux either so i just simply followed wut you did and it all worked. Now only if I can figure ( AGAIN ) what my password for MJ is. In my router it shows as asterisk. do you know how to reveal it? i tried different softs for it but no go. otherwise i will go thru getting the password from dumped memory all over again. anyways Thank you and Two Thumbs UP for that perfact guide.
Back to top
View user's profile Send private message
oldtimercurt
Dan isn't smart enough to hire me


Joined: 07 Feb 2009
Posts: 281
Location: Pensacola

PostPosted: Wed Jul 29, 2009 12:02 pm    Post subject:

nakamoniel
Try Stroths utility. Works for everyone who read the directions.

OTC
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Fri Jul 31, 2009 12:17 pm    Post subject:

nakamoniel-
I second OTC's recommendation since I use Stroths utility to get my MJ SIP information.

Below is a link to Stroths post which has with a link to download his utility-
http://www.phoneservicesupport.com/stroths-mj-utilities-suite-sip-grabber-upgrader-and-more-t4230.html
Back to top
View user's profile Send private message
wang_12533
MagicJack Newbie


Joined: 10 Jun 2009
Posts: 5

PostPosted: Fri Aug 14, 2009 10:48 am    Post subject: Re: Tomato Version of MJMD5 (aka mjproxy)

Thanks noetic1. Are you able to take the ATA out of network?
Back to top
View user's profile Send private message
Guide_timothy
magicJack Apprentice


Joined: 15 Dec 2008
Posts: 21

PostPosted: Tue Aug 18, 2009 6:08 am    Post subject: HELP

#5Upload mjproxy to Tomato (jffs) with putty using Windows command prompt with -scp option
Open a Windows command window (via Start/Run/Cmd) and navigate to the putty directory. Notice in the screenshot below I executed the command from the following directory- C:\Program Files\PuTTY
Then type in the following command-
"pscp -scp mjproxy [email protected]:/jffs" (assuming 192.168.1.1 is your router IP)

HELP im having trouble with step 5 Crying or Very sad Crying or Very sad what ever i enter into CMD thingy it says ts not recognised as an internal or external command or operable program or batch file.. i know it has something to do with pscp file on that puTTY thingy can someone help me plz Crying or Very sad
maybe you can do it with remote desktop connection on messenger or something anyways I got DDWRT version working perfectly but everyone says tomato firmware is best
Back to top
View user's profile Send private message
ssudarshan75
magicJack Apprentice


Joined: 22 May 2009
Posts: 13

PostPosted: Fri Aug 21, 2009 10:35 am    Post subject:

noetic1 wrote:
nakamoniel-
I second OTC's recommendation since I use Stroths utility to get my MJ SIP information.

Below is a link to Stroths post which has with a link to download his utility-
http://www.phoneservicesupport.com/stroths-mj-utilities-suite-sip-grabber-upgrader-and-more-t4230.html


V1.6 is no longer able to retrieve SIP info.how do we get it?
Back to top
View user's profile Send private message
ssudarshan75
magicJack Apprentice


Joined: 22 May 2009
Posts: 13

PostPosted: Fri Aug 21, 2009 7:26 pm    Post subject: Last step help plzzz

So i got hold of my password from password retriever, I have Innomedia MTA6238Re. I entered the password there. Now after i connect this ATA, i still see as not registered, when i run top i cannot find mjproxy running?What is missing.

# mjproxy listen-ip|0.0.0.0 5070 proxy01.dallas.talk4free.com 5070 mypassword
-sh: 0.0.0.0: not found
Back to top
View user's profile Send private message
fastrthnu
MagicJack Newbie


Joined: 25 Aug 2009
Posts: 2

PostPosted: Tue Aug 25, 2009 10:06 pm    Post subject:

I'ved followed everything and it is perfectly laid out. However, I am a noob at this and cannot figure out how to get my Linsys pap2t to work with this.
The last step is to log into the ata and confirm that is is on line.
I think this is the crucial step I am missing and cannot figure out.
I assume with mjproxy i no longer need to have magic jack plugged into the cpu. but without it in I dont get a dial tone.
Can someone steer me in the right direction
Thanks
Back to top
View user's profile Send private message
steve_togo
MagicJack Expert


Joined: 09 Dec 2008
Posts: 84

PostPosted: Wed Aug 26, 2009 6:48 pm    Post subject:

fastrthnu wrote:
I'ved followed everything and it is perfectly laid out. However, I am a noob at this and cannot figure out how to get my Linsys pap2t to work with this.
The last step is to log into the ata and confirm that is is on line.
I think this is the crucial step I am missing and cannot figure out.
I assume with mjproxy i no longer need to have magic jack plugged into the cpu. but without it in I dont get a dial tone.
Can someone steer me in the right direction
Thanks


ATA is a device like ur linksys router... Do you have that device it is of the same size as a wireless router
Back to top
View user's profile Send private message
steve_togo
MagicJack Expert


Joined: 09 Dec 2008
Posts: 84

PostPosted: Wed Aug 26, 2009 6:50 pm    Post subject: Re: Last step help plzzz

ssudarshan75 wrote:
So i got hold of my password from password retriever, I have Innomedia MTA6238Re. I entered the password there. Now after i connect this ATA, i still see as not registered, when i run top i cannot find mjproxy running?What is missing.

# mjproxy listen-ip|0.0.0.0 5070 proxy01.dallas.talk4free.com 5070 mypassword
-sh: 0.0.0.0: not found


You should find it... Where are u running it from? From a telnet session or have u saved it as a command?
Back to top
View user's profile Send private message
fastrthnu
MagicJack Newbie


Joined: 25 Aug 2009
Posts: 2

PostPosted: Wed Aug 26, 2009 11:00 pm    Post subject:

steve_togo wrote:
fastrthnu wrote:
I'ved followed everything and it is perfectly laid out. However, I am a noob at this and cannot figure out how to get my Linsys pap2t to work with this.
The last step is to log into the ata and confirm that is is on line.
I think this is the crucial step I am missing and cannot figure out.
I assume with mjproxy i no longer need to have magic jack plugged into the cpu. but without it in I dont get a dial tone.
Can someone steer me in the right direction
Thanks


ATA is a device like ur linksys router... Do you have that device it is of the same size as a wireless router


Steve-
Thanks for helping.
I have a linksys pap2t that i recently purchased. I have this hooked into one of the ports of my Tomato router.
Back to top
View user's profile Send private message
ssudarshan75
magicJack Apprentice


Joined: 22 May 2009
Posts: 13

PostPosted: Fri Aug 28, 2009 7:21 pm    Post subject: Re: Last step help plzzz

steve_togo wrote:
ssudarshan75 wrote:
So i got hold of my password from password retriever, I have Innomedia MTA6238Re. I entered the password there. Now after i connect this ATA, i still see as not registered, when i run top i cannot find mjproxy running?What is missing.

# mjproxy listen-ip|0.0.0.0 5070 proxy01.dallas.talk4free.com 5070 mypassword
-sh: 0.0.0.0: not found


You should find it... Where are u running it from? From a telnet session or have u saved it as a command?


Running from a telnet session...
Back to top
View user's profile Send private message
sarsipius
MagicJack Newbie


Joined: 29 Aug 2009
Posts: 1

PostPosted: Sat Aug 29, 2009 1:50 am    Post subject: Re: Last step help plzzz

ssudarshan75 wrote:
steve_togo wrote:
ssudarshan75 wrote:
So i got hold of my password from password retriever, I have Innomedia MTA6238Re. I entered the password there. Now after i connect this ATA, i still see as not registered, when i run top i cannot find mjproxy running?What is missing.

# mjproxy listen-ip|0.0.0.0 5070 proxy01.dallas.talk4free.com 5070 mypassword
-sh: 0.0.0.0: not found


You should find it... Where are u running it from? From a telnet session or have u saved it as a command?


Running from a telnet session...


ssudarshan75, take out the listen-ip| part. run:
Code:
 mjproxy 0.0.0.0 5070 proxy01.dallas.talk4free.com 5070 mypassword
Back to top
View user's profile Send private message
newwonder01
magicJack Apprentice


Joined: 02 Feb 2008
Posts: 21

PostPosted: Sun Aug 30, 2009 5:40 am    Post subject:

Hi, are u able to call and receive using innomedia device, I am having problem of calling, immediately is going to busy tone.
Back to top
View user's profile Send private message
nakamoniel
MagicJack Newbie


Joined: 29 Dec 2008
Posts: 9

PostPosted: Thu Oct 15, 2009 1:38 am    Post subject: WRTP54G KEEPS REBOOTING

HI GUYS, my router is acting up really weired, i have my tomato on wr859g at 192.168.1.1 and linksys router (wrtp54g) at 192.168.15.1 both have dhcp enabled. now when i dont have sip info everything works flow less as far as having my wr850g in CLIENT MODE running MJPROXY and linksys as router, but as soon as i try to register sip ( either majicjack or sipgate) all hell breaks loose and router would keep rebooting over and over and over again. however it would go stable after few minutes/hours, would keep working for few days and drop out again. Is it a known issue? Any one had troubleshot it or know the solution?
Back to top
View user's profile Send private message
RobbyG
magicJack Apprentice


Joined: 26 Dec 2009
Posts: 17

PostPosted: Sat Jan 02, 2010 3:34 pm    Post subject:

Thanks noetic1 for the great guide. Was able to setup the proxy on my WRT54GL with Tomato yesterday and everything is working great! Razz
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Mon Jan 11, 2010 3:44 pm    Post subject: Stuck on step # 7

I am using Linksys WRT54G-TM and using Tomato 1.27. I have run into a prolem on step number 7. I entered "chmod mjproxy to 755" (no quotes) and it says it can not be found. I am at a loss here, because I have no knowledge of programming linux. It appears that the mjproxy is not loading in router.

Also it says to Telnet, but doesn't show clicking telnet. I thought telnet used port 23. I am stumped at this level. Any help from here would be appreciated.

Thanks,


Mike
Back to top
View user's profile Send private message
twice
MagicJack Newbie


Joined: 01 Jun 2008
Posts: 4

PostPosted: Tue Jan 12, 2010 12:59 am    Post subject: chmod

make sure u are in the jffs directory
and "chmod 755 mjproxy"
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Tue Jan 12, 2010 12:19 pm    Post subject:

I think I see my mistake. In step 5, I uploaded to 192.168.1.1, but forgot to add /JFFS. I will try that when I go home and update my progress. Did I have to make a JFFS folder, or by enabling in router it is made automatically?



Thanks
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Wed Jan 13, 2010 12:10 am    Post subject:

I made it through to step 10, and this is the command that shows up in Putty.

/jffs/mjproxy 0.0.0.0 5070 proxy01.miami.talk4free.com 5070 MJpassword

In the tutorial it has same, except no jffs/ before mjproxyxxxxxxxx

I am not getting the line connected. Did I somehow load mj proxy in wrong directory?

Any ideas?


Thanks,


Mike
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Thu Jan 14, 2010 8:08 am    Post subject:

anyone?
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Sat Jan 16, 2010 9:41 pm    Post subject:

Guys,

I got it working. I realized I had wrong setting in ATA . I had proxy setting set at 192.168.1.101. It should have been 192.168.1.1.

I appreciate all the help.


Thanks,

Mike
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Mon Jan 18, 2010 6:25 pm    Post subject:

Mike - Glad you were able to work through the settings.

I've been using this setup since my original post and it has been running solid. I'm sure you won't be disappointed.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Mon Jan 18, 2010 11:26 pm    Post subject:

I am back. Everything was working great until I had to disconnect my router,ATA etc.. today to paint my computer room. I hooked everything back up and it is not working.

I telnet and used the top command, and I do not see MJ proxy command. I then started fresh with the instructions, and once again when I use top command, I don't see MJ proxy in list.

Am I missing something?


Thanks,

Mike
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Mon Jan 18, 2010 11:48 pm    Post subject:

That is strange. I actually powered down my modem, router (running Tomato/MJMD5), PAP2NA, 1GB switch and NAS because my NAS was acting up and I couldn't access files in it.

I powered everything back up and verified I had a dial tone on my home phone and that I could ring my cell phone.

I recommend unplugging your router, waiting 30 seconds and then plugging it back in to see if it kicks off the MJMD5 command. If not, then just telnet to your router and manually enter the command and run the 'top' command to verify that mjproxy is running.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Tue Jan 19, 2010 12:23 am    Post subject:

When you say manually enter command, could you tell me what to enter.




Thanks,


Mike
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Tue Jan 19, 2010 12:36 am    Post subject:

command = mjproxy 0.0.0.0 5070 proxy01.chicago.talk4free.com 5070 your_MJ_password (with your correct proxy and password)

Did you verify that you successfully completed step 8 where it says to 8. Put command line in Tomato Administration/Scripts/Init tab ?

This step automatically executes that command after the specified wait/sleep time when you reboot your router.

Don't forget that it might take 3-5 minutes before your ATA changes to 'Online' status.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Tue Jan 19, 2010 12:51 am    Post subject:

This is what I have in my scripts - sleep 30
/jffs/mjproxy 0.0.0.0 5070 proxy01.miami.talk4free.com 5070 my password

Do I need that JFFS. That is what I had previously when it was working.

I appreciate your help. It is probably something simple, most likely operator error.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Tue Jan 19, 2010 1:25 am    Post subject:

I manually typed command in, and now when I type "top", the command is listed. I will keep you posted if it works. I will wait 3-5 minutes.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Tue Jan 19, 2010 10:15 am    Post subject: Got it working !!!

It seems I had to manually load mjproxy in the putty program. Thanks, all is working well.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Fri Jan 29, 2010 11:39 pm    Post subject: automatically run script

Whenever I need to reset my router my script does not automatically run. I have to manually put it in putty. Any ideas why this is happening?
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Fri Jan 29, 2010 11:51 pm    Post subject:

This typically means that you are executing the command from the wrong folder (i.e., mjproxy is not in the jffs folder).

Telnet to your router, go to the 'jffs' directory and type ls to 'list the files in the directory'. and doublecheck that mjproxy is in the jffs folder. You should see mjproxy returned.
Back to top
View user's profile Send private message
mjc8870
MagicJack Contributor


Joined: 12 Nov 2008
Posts: 64

PostPosted: Sat Jan 30, 2010 2:59 pm    Post subject:

I figured it out. I was missing a backslash before JFFS in command.
Back to top
View user's profile Send private message
p13482
MagicJack Newbie


Joined: 31 Jan 2010
Posts: 3

PostPosted: Sun Jan 31, 2010 5:21 pm    Post subject:

Confused OK OK I just joined this forum and have several questions.
1) Is the password I enter into the Tomato INIT script the password I get from the SIPDump ?
2) Is the User ID & pasword I enter into my ATA the info I get from the SIPDump ? ie. [email protected] & 0123456789abcdef0123456789abcdef

TNX for any help

P
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Sun Jan 31, 2010 10:56 pm    Post subject:

p13482 wrote:
Confused OK OK I just joined this forum and have several questions.
1) Is the password I enter into the Tomato INIT script the password I get from the SIPDump ?
2) Is the User ID & pasword I enter into my ATA the info I get from the SIPDump ? ie. [email protected] & 0123456789abcdef0123456789abcdef

TNX for any help

P


1) Is the password I enter into the Tomato INIT script the password I get from the SIPDump ? Yes
2) Is the User ID & pasword I enter into my ATA the info I get from the SIPDump? Yes ie. [email protected] & 0123456789abcdef0123456789abcdef
User ID = E727555555501 (you don't need the @talk4free.com)
Password = the password from the SIPDump
Back to top
View user's profile Send private message
p13482
MagicJack Newbie


Joined: 31 Jan 2010
Posts: 3

PostPosted: Mon Feb 01, 2010 2:59 pm    Post subject:

noetic1:

Thanks for your reply. No joy however. Could you look at the attached SPA-3102 screen dump and see if you can see any issues. (my phone is obviously not 555-5555)

I have confirmed that mjproxy is running on the router. I also read somewhere that people have gotten their ATAs to provision without it. (?)

thanks

P
[img]http://rapidshare.com/files/344447903/SPA-3102.jpg.html
[/img]
Back to top
View user's profile Send private message
noetic1
MagicJack Contributor


Joined: 14 Oct 2008
Posts: 65

PostPosted: Mon Feb 01, 2010 10:47 pm    Post subject:

Differences I noticed compared to my settings.

NAT Mapping Enable: No
Outbound proxy: blank
Use Outbound proxy: No
Use Auth ID: No
Back to top
View user's profile Send private message
p13482
MagicJack Newbie


Joined: 31 Jan 2010
Posts: 3

PostPosted: Tue Feb 02, 2010 1:06 pm    Post subject:

Very Happy Very Happy Very Happy

noetic1

Thanks for your help ! I fixed the discrepancies and also found I had the wrong password. (that 20 character sucker is elusive)

P
Back to top
View user's profile Send private message
richardtaur
Dan isn't smart enough to hire me


Joined: 17 Mar 2008
Posts: 123

PostPosted: Sat Mar 06, 2010 5:08 pm    Post subject: Hi~

This is the easiest way to use MJ w/o USB. From QOS, I notice that MJ uses a lot of bandwidth around 10K, not even using a lot of bandwidth, the quality is not that great. Do you guys experience the same thing?
Back to top
View user's profile Send private message
silvereyes
MagicJack Newbie


Joined: 12 Mar 2010
Posts: 3

PostPosted: Fri Mar 12, 2010 11:02 am    Post subject:

I'm new to this. I have several questions if someone can help.
I do have two routers with tomato firmware on them.
What is the exact purpose of this guide? Does magic jack not work on tomato firmware otherwise?

My other question, I have two routers connected to eachother via a very long ethernet cable. I had to disable DHCP in router B to get this going. I'm planning to get 2 magic jacks, one for each computer that is next to the routers. Do I need to follow this guide to both routers or only router A?
(router A close to cable modem, router B is far away)

I appreciate any help out there
Back to top
View user's profile Send private message
richardtaur
Dan isn't smart enough to hire me


Joined: 17 Mar 2008
Posts: 123

PostPosted: Fri Mar 12, 2010 4:17 pm    Post subject:

silvereyes wrote:
I'm new to this. I have several questions if someone can help.
I do have two routers with tomato firmware on them.
What is the exact purpose of this guide? Does magic jack not work on tomato firmware otherwise?

My other question, I have two routers connected to eachother via a very long ethernet cable. I had to disable DHCP in router B to get this going. I'm planning to get 2 magic jacks, one for each computer that is next to the routers. Do I need to follow this guide to both routers or only router A?
(router A close to cable modem, router B is far away)

I appreciate any help out there

If you are using tomato on two routers. You can use Access Point + WDS. So, the 2nd router doesn't need to connect the cable from router 1 to router 2. You can search WDS on F&Q at http://www.polarcloud.com/tomatofaq for the configuration. This topic at the first post is to guide you how to use MJ without MJ plugged in to the PC. But you will have to get ATAs. This MJproxy only needs to be configured on router A.
Back to top
View user's profile Send private message
silvereyes
MagicJack Newbie


Joined: 12 Mar 2010
Posts: 3

PostPosted: Fri Mar 12, 2010 6:09 pm    Post subject:

thank you richardtaur for the help. I have no choice but to connect the two routers via ethernet cable as the distance is huge, about 200feet and several brick walls in between. I guess I'll have to do more reading as I'm still kind of lost. Are you suggesting the MJ can be connected to router only and not thru pc? And where do I get an ATA?
Back to top
View user's profile Send private message
richardtaur
Dan isn't smart enough to hire me


Joined: 17 Mar 2008
Posts: 123

PostPosted: Fri Mar 12, 2010 7:07 pm    Post subject:

I use HT286. It is small size and does the job. You don't need to connect MJ at all. You will put SIP info on ATA then connect ATA to the router. Therefore, you don't need to leave computer on in order to make phone calls or receive phone calls.
Back to top
View user's profile Send private message
richardtaur
Dan isn't smart enough to hire me


Joined: 17 Mar 2008
Posts: 123

PostPosted: Sat Mar 13, 2010 5:11 pm    Post subject:

Is there any tool for spoofing caller id for tomato version?
Back to top
View user's profile Send private message
kuhntech
MagicJack Contributor


Joined: 15 Dec 2009
Posts: 63
Location: Chico, CA

PostPosted: Tue Mar 16, 2010 5:05 pm    Post subject:

When I run the following command:

mjproxy 0.0.0.0 5070 vms3.sacramento.talk4free.com 5070 MJPassword

I get the error Network Address Invalid. This is what wireshark told me my proxy was. I also tried changing it to proxy01.sacramento and proxy01.chicago but it gives me the same error.
Back to top
View user's profile Send private message Visit poster's website
crackerjack
Dan Should Pay Me


Joined: 16 Nov 2007
Posts: 784

PostPosted: Tue Mar 16, 2010 10:25 pm    Post subject:

richardtaur wrote:
Is there any tool for spoofing caller id for tomato version?

Your caller-id is hard coded on the MJ server side. Spoofing hasn't worked from MJ since at least 18 months ago. Thanks to the knuckleheads who abused the secret.
Back to top
View user's profile Send private message
richardtaur
Dan isn't smart enough to hire me


Joined: 17 Mar 2008
Posts: 123

PostPosted: Tue Mar 16, 2010 10:58 pm    Post subject:

I see. ~_~
Back to top
View user's profile Send private message
richardtaur
Dan isn't smart enough to hire me


Joined: 17 Mar 2008
Posts: 123

PostPosted: Tue Mar 16, 2010 11:02 pm    Post subject:

kuhntech wrote:
When I run the following command:

mjproxy 0.0.0.0 5070 vms3.sacramento.talk4free.com 5070 MJPassword

I get the error Network Address Invalid. This is what wireshark told me my proxy was. I also tried changing it to proxy01.sacramento and proxy01.chicago but it gives me the same error.


I use
Code:
mjproxy 0.0.0.0 5070 proxy01.chicago.talk4free.com 5070 MJPassword
.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Unofficial magicJack Forum -> magicJack Tips, Tricks, and Hacks All times are GMT - 4 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Powered by phpBB Ultra Turbo Extended Edition Live © 2001-9999, phpBB Group
magicJack and magicJack Plus are trademarks of magicJack LLP. This website is in no way affiliated, endorsed, or sponsored by magicJack LLP, and is an unofficial forum for consumers to openly communicate regarding their experiences with the magicJack products.