Unofficial magicJack Forum

Unofficial magicJack Forum

Your Unofficial magicJack and magicJack Plus phone service information resource
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
Trying... Ringing.... Disconnecting...

 
Post new topic   Reply to topic    Unofficial magicJack Forum -> Magic Jack Technical Support
View previous topic :: View next topic  
Author Message
coryj
MagicJack Newbie


Joined: 03 Dec 2008
Posts: 5

PostPosted: Fri Feb 20, 2009 6:29 pm    Post subject: Trying... Ringing.... Disconnecting...

Hello,

I have been searching the forums for a possible answer. I am sure it is related to the fact that I am trying to use my MJ on Windows Server 2008 (x64). The software installed just fine. If I make a call to my cell phone, It says "Trying" for 7 seconds. At 8 seconds, it says "Ringing" briefly and then goes right back to "Ready to call". On my cell phone, I see a missed call from the number, but it doesn't even connect long enough to ring once.

If I call the MJ from my cell phone, it doesn't ring at all and doesn't show up in MJ.

I've been searching around and can't figure it out. Does anyone have any ideas?
Back to top
View user's profile Send private message
nijap
MagicJack Newbie


Joined: 04 Feb 2009
Posts: 5

PostPosted: Thu Feb 26, 2009 3:10 pm    Post subject:

I have the same problem occasionally. I am using too many programs when this happens. If I close down a couple, MJ works fine. I think I am over loading the computer capacity/memory or what ever.
Back to top
View user's profile Send private message
coryj
MagicJack Newbie


Joined: 03 Dec 2008
Posts: 5

PostPosted: Thu Feb 26, 2009 3:11 pm    Post subject:

I don't think that is the issue for me. It is a q9300, 4GB RAM
Back to top
View user's profile Send private message
coryj
MagicJack Newbie


Joined: 03 Dec 2008
Posts: 5

PostPosted: Thu May 21, 2009 2:59 am    Post subject:

Does anyone have it working successfully on Server 2008 (x64)? I am still unable to use my magicjack on this machine
Back to top
View user's profile Send private message
dtgoodwin
MagicJack Newbie


Joined: 22 May 2009
Posts: 1

PostPosted: Fri May 22, 2009 2:46 pm    Post subject:

Unfortunately, I am running into a similar issue. I also have 2K8 x64 server. I am running an AMD X2 5200+ processor with 8 GB of RAM. I normally have 3 virtual machines running via Hyper-V, but even turning them off I get the same issue, only I get about 2 seconds of trying, then it disconnects. Incoming calls show as red with an "x". If I remove MJ from the machine, I can make calls for anywhere from 5-10 minutes and then it fails. Eventually, I lose my dial tone.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Unofficial magicJack Forum -> Magic Jack Technical Support All times are GMT - 4 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Powered by phpBB Ultra Turbo Extended Edition Live © 2001-9999, phpBB Group
magicJack and magicJack Plus are trademarks of magicJack LLP. This website is in no way affiliated, endorsed, or sponsored by magicJack LLP, and is an unofficial forum for consumers to openly communicate regarding their experiences with the magicJack products.