Linksys RTP300 Configuration For MJ

macman4hire · Post by **macman4hire** » Sat May 09, 2009 9:25 pm

This is an RTP300 configuration for the MagicJack with screen shots. I would like to thank MagicDump for his PAP2 configuration example that I consulted. I also would like to thank mberlant for his dialing plan that was used in this set up. Last but not least stroths for his MagicJack Utilities Suite v1.6 to pull your SIP credentials from your MagicJack. I hope it helps all the forum members that own Linksys RTP300 and wish to use with their MagicJack.

stroths's MagicJack Utilities Suite v1.6 http://rapidshare.com/files/181629789/M ... s_v1.6.zip

MagicDump's PAP2 configuration file http://rapidshare.com/files/208210096/PAP2TMJ.config use this to copy and pasted any of the fields you can not completely see in screen shots.

mbarlent's dial plan

Code: Select all

([1235-9]11!|411S0|<:1311>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0| 1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!|011!)

[/code]

wirelessrat · Post by **wirelessrat** » Sat May 09, 2009 10:38 pm

Ditto

macman4hire · Post by **macman4hire** » Sun May 10, 2009 10:33 pm

Hope this helps wirelessrat.

911pcdoc · Post by **911pcdoc** » Wed May 13, 2009 12:28 am

ok did i miss part there i have a rtp300 and want to set it up to replace the silver dongal!! where do i find the info for my account and then what to i do with tis file yes i am new so not to much flameing please!

oldtimercurt · Post by **oldtimercurt** » Wed May 13, 2009 7:17 am

911pcdoc

http://www.phoneservicesupport.com/stro ... t4230.html will help with your MJ info.

http://www.phoneservicesupport.com/magi ... t5066.html will help with setup.

OTC

911pcdoc · Post by **911pcdoc** » Wed May 13, 2009 1:02 pm

thank you for that info i am gonna be trying to configure my old rtp300 from (another provider)i have reflashed and is wide open now i will let you all know how it turns out!

911pcdoc · Post by **911pcdoc** » Thu May 14, 2009 11:37 am

ok i got i most of it! i have a dial tone and it seems to be up but when i dial i get a rapid busy???? on any number please help!

macman4hire · Post by **macman4hire** » Thu May 14, 2009 12:14 pm

1.You want to try lowering the Register Expires: setting which is listed under the either Line 1 or 2 depending on which line you choose to configure your MagicJack under. Set the Register Expires: to 60 and see if that corrects the problem.

2.Check you dialing plan. Did use mberlant's dialing if so replace the 311 with your local area code. Also try the complete 11 digit telephone number to place a call.

911pcdoc · Post by **911pcdoc** » Thu May 14, 2009 12:19 pm

actually i got it going i used different dialing rules! to fix it thanks now seems like the delay after dialing is too long like 10 to 15 sec before it starts to ring???? is there a setting for this??? sorry but yes i am new! to this but i am vary vary glad that its not on the pc or that silver thing!! anymore!

macman4hire · Post by **macman4hire** » Thu May 14, 2009 12:25 pm

Good deal! Just remember to never run your ATA and the USB Magic Jack dongle at the same time. This could get your service terminated.

911pcdoc · Post by **911pcdoc** » Thu May 14, 2009 12:37 pm

yea thats kinda obvious but you know some peps might try it lol!! you just you all just made me love my magic jack all over again!!!!

911pcdoc · Post by **911pcdoc** » Thu May 14, 2009 1:38 pm

only problem now this delay on dial out is not good! any advice?
also all inbound calls are going stright to vm?? Please help!
it seems that somewhere i missed something i see on the onfo screen call back active: NO ??? PLEASE I NEED HELP!

macman4hire · Post by **macman4hire** » Thu May 14, 2009 2:19 pm

Did you lower the Register Expires: value to 60?
Did switch to mberlant's dial plan?

mberlant's dial plan below

Code: Select all

([1235-9]11!|411S0|<:1311>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0| 1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!|011!)

Note the replace the 1<:1311> with your area code <:1XXX>

911pcdoc · Post by **911pcdoc** » Thu May 14, 2009 2:31 pm

ok i have set it to 60 and switched to the dial plan and edited the area code! seems better there but i can get calls AWWWW

Hook State: On Registration State: Registered
Last Registration At: 5/14/2009 14:28:55 Next Registration In: 30 s
Message Waiting: No Call Back Active: No[/u][/i]

911pcdoc · Post by **911pcdoc** » Thu May 14, 2009 3:44 pm

ok here it is i have it all working 100% or so it seems looks like my crappy router as not routing correctly so no calls were coming i have it all working now!!! thank you all so much for the help here and i will try to help those out that need help here as well! this was an easier project then i thought at first! as i said love this magic jack agine!!

macman4hire · Post by **macman4hire** » Thu May 14, 2009 4:02 pm

Glad to hear your setup is working and that you will help out other forum members.

911pcdoc · Post by **911pcdoc** » Fri May 15, 2009 1:52 am

question on dialing i think i want to set up dialing *123 for voicmail ie
*123 = xxx-xxx-xxxx do you know how i can do this??

anant · Post by **anant** » Sat May 16, 2009 5:41 pm

I have a RTP300 locked with Vonage service. Has anyone unlocked it to use with MJ? If this is already discussed in the forum I would appreciate if someone could guide me. Thanks in anticipation.

anant

ingenio · Post by **ingenio** » Sat May 16, 2009 11:43 pm

UPDATTING DATE AND TIME

How do I DO?

I need to keep that information Update.

What Do I to need to do?

Thanks you.

911pcdoc · Post by **911pcdoc** » Sat May 16, 2009 11:51 pm

anant wrote:I have a RTP300 locked with Vonage service. Has anyone unlocked it to use with MJ? If this is already discussed in the forum I would appreciate if someone could guide me. Thanks in anticipation.

anant

i am using old v**age rtp300 now i was able to unlock it look here

1) Download the modified firmware from http://www.mediafire.com/?bwtsovg049w (if its not there pm me and i can e-mail you the bin)

2) connect your computer to the rtp300 and go to http://192.168.15.1
Default username is "admin" password is "admin"

3) next, go to http://192.168.15.1/update.html and enter "user" as the username and "tivonpw" as the password without quotes of course. If the password doesn't work try user / user or admin / admin if that dont work theres no hope and it cant be used! dont ask for more help!

4) Browse for the firmware on your computer you downloaded above and click upgrade!

then see the above pages for the configuration of the router!

911pcdoc
rtp-300

911pcdoc · Post by **911pcdoc** » Sat May 16, 2009 11:58 pm

ingenio wrote:UPDATTING DATE AND TIME

How do I DO?

I need to keep that information Update.

What Do I to need to do?

Thanks you.

did you setup the ntp servers in the system page of the voice settings?

ingenio · Post by **ingenio** » Sun May 17, 2009 1:41 am

YES I DIT IT, BUT NEVER UPDATE AUTOMATICALLY.

MAYBE I NEED SET OTHER THING.

PLEASE HELP ME.

THANKS YOU

911pcdoc wrote:
ingenio wrote:UPDATTING DATE AND TIME

How do I DO?

I need to keep that information Update.

What Do I to need to do?

Thanks you.
did you setup the ntp servers in the system page of the voice settings?

911pcdoc · Post by **911pcdoc** » Sun May 17, 2009 3:23 am

if the ntps are set and your reg time is set each time it resync it should get time !! time this might be odd but call your self form a cell or something it might kick the new time through the system!!

trek101 · Post by **trek101** » Thu May 21, 2009 7:38 pm

The reason why it takes 10 to 15 seconds for your call to connect is the interdigit long time by default is set for 10 seconds. Which means that the last digit dialed the ATA waits for about 10 seconds before forwarding the dialing information to the call server.

To change that just go to the Voice tab then Admin login link and then choose the Switch to advanced mode link. Click on the regional tab and go about a half way down. Change the Interdigit Long Timer to 5 seconds. That should shorten the delay on connecting your call after the last digit has been dialed...

wirelessrat · Post by **wirelessrat** » Thu May 21, 2009 8:30 pm

Nice post. I got mine working, but I am expecting bugs. This should help me take care of any I suspect.

Thanks once again macman

otacon6530 · Post by **otacon6530** » Sun May 24, 2009 6:01 pm

sip user agent name?

it is cut off. what is the rest of it?

---------------------------------
I copied yours exactly except for the sip user agent name and I can not even get a dial tone.

on the information page it says registration Failed

macman4hire · Post by **macman4hire** » Sun May 24, 2009 7:31 pm

Just down load MagicDump's PAP2 configuration file and open the file using a text editor such as notepad. Find the part of the configuration that you can completely read in the screens shots and copy and paste that section into your RTP300 configuration. It clearly states this in the first post of this thread.

Good luck!

otacon6530 · Post by **otacon6530** » Sun May 24, 2009 7:36 pm

Sorry I have been at this for a long time and I must have over looked it.

No still does not work.

I do not even know where to go from here.

My registration State below Fails. Any suggestions?

Information
Product Name: rtp300 Serial Number: CJM00E956944
Software Version: 3.1.22 Hardware Version: 1.00.03
MAC Address: 0014BF910AC9 Client Certificate: Installed
System Status
Current Time: 1/1/2003 12:02:29 Elapsed Time: 00:02:29
RTP Packets Sent: 0 RTP Bytes Sent: 0
RTP Packets Recv: 0 RTP Bytes Recv: 0
SIP Messages Sent: 64 SIP Bytes Sent: 31251
SIP Messages Recv: 0 SIP Bytes Recv: 0
External IP: 67.236.70.150
Line 1 Status
Hook State: On Registration State: Failed
Last Registration At: 0/0/0 00:00:00 Next Registration In:
Message Waiting: Yes Call Back Active: No
Last Called Number: Last Caller Number:
Mapped SIP Port: 12986
Call 1 State: Idle Call 2 State: Idle
Call 1 Tone: None Call 2 Tone: None
Call 1 Encoder: Call 2 Encoder:
Call 1 Decoder: Call 2 Decoder:
Call 1 FAX: Call 2 FAX:
Call 1 Type: Call 2 Type:
Call 1 Remote Hold: Call 2 Remote Hold:
Call 1 Callback: Call 2 Callback:
Call 1 Peer Name: Call 2 Peer Name:
Call 1 Peer Phone: Call 2 Peer Phone:
Call 1 Duration: Call 2 Duration:
Call 1 Packets Sent: Call 2 Packets Sent:
Call 1 Packets Recv: Call 2 Packets Recv:
Call 1 Bytes Sent: Call 2 Bytes Sent:
Call 1 Bytes Recv: Call 2 Bytes Recv:
Call 1 Decode Latency: Call 2 Decode Latency:
Call 1 Jitter: Call 2 Jitter:
Call 1 Round Trip Delay: Call 2 Round Trip Delay:
Call 1 Packets Lost: Call 2 Packets Lost:
Call 1 Packet Error: Call 2 Packet Error:
Call 1 Mapped RTP Port: Call 2 Mapped RTP Port:
Line 2 Status
Hook State: On Registration State: Not Registered
Last Registration At: Next Registration In:
Message Waiting: No Call Back Active: No
Last Called Number: Last Caller Number:
Mapped SIP Port:
Call 1 State: Idle Call 2 State: Idle
Call 1 Tone: None Call 2 Tone: None
Call 1 Type: Call 2 Type:
Call 1 Encoder: Call 2 Encoder:
Call 1 Decoder: Call 2 Decoder:
Call 1 FAX: Call 2 FAX:
Call 1 Remote Hold: Call 2 Remote Hold:
Call 1 Callback: Call 2 Callback:
Call 1 Peer Name: Call 2 Peer Name:
Call 1 Peer Phone: Call 2 Peer Phone:
Call 1 Duration: Call 2 Duration:
Call 1 Packets Sent: Call 2 Packets Sent:
Call 1 Packets Recv: Call 2 Packets Recv:
Call 1 Bytes Sent: Call 2 Bytes Sent:
Call 1 Bytes Recv: Call 2 Bytes Recv:
Call 1 Decode Latency: Call 2 Decode Latency:
Call 1 Jitter: Call 2 Jitter:
Call 1 Round Trip Delay: Call 2 Round Trip Delay:
Call 1 Packets Lost: Call 2 Packets Lost:
Call 1 Packet Error: Call 2 Packet Error:
Call 1 Mapped RTP Port: Call 2 Mapped RTP Port:

otacon6530 · Post by **otacon6530** » Sun May 24, 2009 7:38 pm

oh I forgot to add this. When I pick up the phone I do not get a dial tone. I know it is connecting to the router because **** works

otacon6530 · Post by **otacon6530** » Mon May 25, 2009 12:59 am

ok I tinkered with it and got it to work. I have no idea how but I am not complaining.

Is there any way to get the static in the background either gone or better than it is now?

I will try to mess with codecs and see if that helps.

911pcdoc · Post by **911pcdoc** » Fri Jun 05, 2009 12:46 am

only the 711 codecs will work for it!!!

JohnnyPhilko · Post by **JohnnyPhilko** » Fri Jun 05, 2009 8:35 am

wrong thread

JohnnyPhilko · Post by **JohnnyPhilko** » Fri Jun 05, 2009 8:38 am

Hi,

I have Magic Jack and an open unlocked RTP300. I just read this thread with great interest.

Are you saying that by following these instructions I can unplug the MagicJack Usb dongle and plug my phone directly into the RTP300 without having the usb dongle plugged into my computer? Or do I still need the MJ thing plugged into my computer.

Thanks in advance!

macman4hire · Post by **macman4hire** » Fri Jun 05, 2009 3:47 pm

No you can not plug your MagicJack USB dongle into the RTP300. You 1st obtain your SIP credentials using Stroths MagicJack Utilities Suite 1.6 2nd Enter all the setting given in the photo examples including your MagicJacks SIP credentials. Just follow the first post instructions!

Good Luck

JohnnyPhilko · Post by **JohnnyPhilko** » Fri Jun 05, 2009 3:53 pm

I think you might of mis-understood what I was asking. I know I can't plug my Magic Jack USB Dongle into the RPT300.

I'm just asking if this procedure will allow me to plug my phone into the router without having the Magic Jack usb dongle plugged into my computer and use my phone that way after entering in all of the info.

Thus my phone will worrk without having the computer turned on and without seeing the annoying software pop up.

macman4hire · Post by **macman4hire** » Fri Jun 05, 2009 7:02 pm

You got it right! No computer and MagicJack USB dongle.

JohnnyPhilko · Post by **JohnnyPhilko** » Sat Jun 06, 2009 10:49 am

Cool Thanks!! I'm going to give it a try!

911pcdoc · Post by **911pcdoc** » Sat Jun 06, 2009 1:16 pm

good luck and let us know how it goes any troubles please post them here thanks!

JohnnyPhilko · Post by **JohnnyPhilko** » Sat Jun 06, 2009 2:08 pm

Thanks!

I'm working on it now and can't get a dail-tone yet. I'm going to keep poking around and see what I find.

Any help appreciated!

JohnnyPhilko · Post by **JohnnyPhilko** » Sat Jun 06, 2009 4:35 pm

Hi all,

I got it working by not using the

ProxyName = proxy01.********.talk4free.com

That I got from my MagicJack SIP Info

I switched it to proxy1.miami.talk4free.com:5070
and can now get registered and make and receive phone calls including caller ID! Yay!!!

But I am getting an echo on both sides of the call.

Ok, before I even clicked send, I realized that the ******** proxy was missing the :5070 at the end!

So, I switched it to proxy01.********.talk4free.com:5070 and all is working well so far with much less echo!

I hope this helps someone in the future.

TIA

macman4hire · Post by **macman4hire** » Sat Jun 06, 2009 11:11 pm

Glad to hear your RTP300 is up and running.

JohnnyPhilko · Post by **JohnnyPhilko** » Sun Jun 07, 2009 8:24 am

Thanks MacMan! I really love how it works now.

The only problem I have yet to figure out is that my voicemail notification stays on and flashing whether or not I have any messages or not. I shut the feature off in the RTP300, but now I get no notification even when there are messages.

Any ideas appreciated!

macman4hire · Post by **macman4hire** » Sun Jun 07, 2009 11:01 am

The voicemail was working fine for as for indicating that I had new message with a rapid pulsing dial-tone before the regular dial-tone. I however did notice that after retrieving message by calling the MJ number it take time to reset to a cleared message status. I longer use MJ voice mail feature as I find more convenient to use an answer machine that I have set to answer the calls on the third ring. The reason I set the answering machine to answer on the third ring is that the MJ answers on the fourth ring and at this time MJ does not give it user the capability to turn of the voicemail. the advantage is when I return home I don't pick up the phone to check my messages and I still have remote message retrieval by using the answering machine. The disadvantage is a prefer four rings before the answer machine pickups.

JohnnyPhilko · Post by **JohnnyPhilko** » Sun Jun 07, 2009 11:26 am

Ok, thanks! That's probably what I will end up doing unless someone replies with a fix for this.

Thanks for all of the help!

x0r0 · Post by **x0r0** » Wed Jun 10, 2009 3:07 am

JohnnyPhilko wrote:Thanks MacMan! I really love how it works now.

The only problem I have yet to figure out is that my voicemail notification stays on and flashing whether or not I have any messages or not. I shut the feature off in the RTP300, but now I get no notification even when there are messages.

Any ideas appreciated!

hi where did you set to shut off the feature for the voice mail notification on the rtp300?

EDITED: i found it thanks anyways i set

VMWI Serv: NO
MWI Serv: NO

JohnnyPhilko · Post by **JohnnyPhilko** » Wed Jun 10, 2009 8:01 am

x0r0 wrote:
JohnnyPhilko wrote:Thanks MacMan! I really love how it works now.

The only problem I have yet to figure out is that my voicemail notification stays on and flashing whether or not I have any messages or not. I shut the feature off in the RTP300, but now I get no notification even when there are messages.

Any ideas appreciated!

hi where did you set to shut off the feature for the voice mail notification on the rtp300?

EDITED: i found it thanks anyways i set

VMWI Serv: NO
MWI Serv: NO

Wow, I didn't know about those settings. I went to "User one" for line one and set "Message Waiting" to No.

Funny thing is that the voice mail notification seems to be working even with that setting set to no, but it seems to be working better. It does shut off after empting the mailbox, but still takes a long time to reset.

tototio · Post by **tototio** » Thu Jun 11, 2009 12:55 pm

Hi guys,

I am very new to the forum posting. My RTP300 is totally unlocked. I can make Magic jack call outs but I get no call ins. I am also getting a beep beep beep beep beep before I get a stable dial tone.

Help please

Anon · Post by **Anon** » Mon Jul 06, 2009 4:46 pm

tototio wrote:Hi guys,

I am very new to the forum posting. My RTP300 is totally unlocked. I can make Magic jack call outs but I get no call ins. I am also getting a beep beep beep beep beep before I get a stable dial tone.

Help please

I'm not sure but that beep might be an indicator that you have voicemail waiting for you.

Anon · Post by **Anon** » Mon Jul 06, 2009 4:48 pm

I have tried using my RTP300 using the MJMD5 prxoie method and it works great except that my phone won't ring now on incoming calls.

Anyone know what might be causing this?

Any help appreciated!

djaj · Post by **djaj** » Tue Jul 07, 2009 2:56 am

Anon wrote:I have tried using my PTR300 using the MJMD5 prxoie method and it works great except that my phone won't ring now on incoming calls.

Anyone know what might be causing this?

Any help appreciated!

Make sure your Forwarding port is 5070 as well.

magicJack and magicJack Plus Support, Reviews, FAQs and Tricks

Linksys RTP300 Configuration For MJ

Linksys RTP300 Configuration For MJ

Hope this helps!

Stroths Magic wand

unlocking of RTP300 locked with Vonage service

Update TIME and Date

Re: unlocking of RTP300 locked with Vonage service

Re: Update TIME and Date

Re: Update TIME and Date

oops!

Newbie Question

help with RTP300 & Magicjck settings

Re: help with RTP300 & Magicjck settings

Help

Re: Help