ATA Start Working with following setting

fordp301 · Post by **fordp301** » Tue Jun 30, 2009 10:54 am

this is not my work, it was written by az1324

you need to download this MJMD5, which can be found in this thread

After download Extract to Desktop then open it only thing you need to change is your proxy address if you using boston then just xxxx to boston of any other city then put your MJ proxy password in password line then mark on save setting and start service

You would setup your ATA the same way you did normally in the past for MJ but instead of the proxy address and port you would put the ip address of your computer running the proxy like (if your computer proxy is 192.168.1.103 then on proxy setting put 192.168.1.103:5070) and the Listen Port. On the proxy itself you would put the proxy address that you normally would have put in the ATA, the Forward Port (5070), and also your MJ password.

I am Using this and its working good

your computer need to be up and running to make it work.

zixy_tris · Post by **zixy_tris** » Tue Jun 30, 2009 12:08 pm

Will give it at try? Is there a possibility I can run this on just one computer and run all my atas or will I have to use different computer for different atas.
I have like 5-6 ATA's and some are international where I do not have option to run a computer full time as proxy. Is there a possibility I can send them to computer running in US??

alphabeta · Post by **alphabeta** » Tue Jun 30, 2009 12:28 pm

fordp301 wrote:this is not my work, it was written by az1324

you need to download this MJMD5, which can be found in this thread.

Seems 1st step towards the goal to use MJ without the need to run PC all the time.

Thanks..

teddy_b · Post by **teddy_b** » Tue Jun 30, 2009 1:10 pm

zixy_tris wrote:Is there a possibility I can send them to computer running in US??

Although this is theoretically possible, the proxy provided (which is, by the way, came from this thread) is not secured, and if exposed to the internet, everybody in the whole world will be able to connect to it and make calls using the MJ account it's setup with. All they need to know is your MJ phone number (which can be obtained by sniffing the traffic, for example).
To prevent this you'll have to provide your own security measures, i.e. filter clients connecting by IP addresses, or require VPN connection, etc...

xboxuser1 · Post by **xboxuser1** » Tue Jun 30, 2009 4:24 pm

fordp301 wrote:this is not my work, it was written by az1324

you need to download this MJMD5, which can be found in this thread

After download Extract to Desktop then open it only thing you need to change is your proxy address if you using boston then just xxxx to boston of any other city then put your MJ proxy password in password line then mark on save setting and start service

You would setup your ATA the same way you did normally in the past for MJ but instead of the proxy address and port you would put the ip address of your computer running the proxy like (if your computer proxy is 192.168.1.103 then on proxy setting put 192.168.1.103:5070) and the Listen Port. On the proxy itself you would put the proxy address that you normally would have put in the ATA, the Forward Port (5070), and also your MJ password.

I am Using this and its working good

your computer need to be up and running to make it work.

Sound good! ... is it possible to give a screen shot of the ata setting to be sure all the setting are good....

Thanks for this info!

mel2000 · Post by **mel2000** » Tue Jun 30, 2009 5:16 pm

alphabeta wrote:Seems 1st step towards the goal to use MJ without the need to run PC all the time.

I get the impression that keeping your computer turned on is still required.

doctorman · Post by **doctorman** » Tue Jun 30, 2009 7:50 pm

mel2000 wrote:
alphabeta wrote:Seems 1st step towards the goal to use MJ without the need to run PC all the time.
I get the impression that keeping your computer turned on is still required.

this is very useless
please put it in the subject that you need a computer running still...

newtoncd · Post by **newtoncd** » Tue Jun 30, 2009 8:05 pm

fordp301 wrote:this is not my work, it was written by az1324

you need to download this MJMD5, which can be found in this thread

After download Extract to Desktop then open it only thing you need to change is your proxy address if you using boston then just xxxx to boston of any other city then put your MJ proxy password in password line then mark on save setting and start service

You would setup your ATA the same way you did normally in the past for MJ but instead of the proxy address and port you would put the ip address of your computer running the proxy like (if your computer proxy is 192.168.1.103 then on proxy setting put 192.168.1.103:5070) and the Listen Port. On the proxy itself you would put the proxy address that you normally would have put in the ATA, the Forward Port (5070), and also your MJ password.

I am Using this and its working good

your computer need to be up and running to make it work.

I would like to set this up with my thin client and my Linksys ATA. But, the MJMD5 program won't run on my thin client. To the person that wrote the program, can you fix it to run on a thin client? I get an error "application failed to initialize properly 0xc0000135. Click OK to terminate".

Any idea?

Edit: looks like I need to install .net framework, which apparently doesn't do well on a thin client ... more to follow.

doctorman · Post by **doctorman** » Tue Jun 30, 2009 8:08 pm

newtoncd wrote:
fordp301 wrote:this is not my work, it was written by az1324

you need to download this MJMD5, which can be found in this thread

After download Extract to Desktop then open it only thing you need to change is your proxy address if you using boston then just xxxx to boston of any other city then put your MJ proxy password in password line then mark on save setting and start service

You would setup your ATA the same way you did normally in the past for MJ but instead of the proxy address and port you would put the ip address of your computer running the proxy like (if your computer proxy is 192.168.1.103 then on proxy setting put 192.168.1.103:5070) and the Listen Port. On the proxy itself you would put the proxy address that you normally would have put in the ATA, the Forward Port (5070), and also your MJ password.

I am Using this and its working good

your computer need to be up and running to make it work.

I would like to set this up with my thin client and my Linksys ATA. But, the MJMD5 program won't run on my thin client. To the person that wrote the program, can you fix it to run on a thin client? I get an error "application failed to initialize properly 0xc0000135. Click OK to terminate".

Any idea?

non of my business but why the hell use ata with TC at the same time
you have extra money?

just use the TC.

oldtimercurt · Post by **oldtimercurt** » Tue Jun 30, 2009 8:12 pm

doctorman

One possibility, though I haven't tried it yet, is that the call quality used to be considered to be better on the ATA. That's why I'm looking into it.

OTC

newtoncd · Post by **newtoncd** » Tue Jun 30, 2009 8:29 pm

doctorman wrote: non of my business but why the hell use ata with TC at the same time you have extra money?

just use the TC.

I am desperately trying to get rid of the dreaded beep. It is driving us crazy... and to be honest, I love playing around technology stuff.

fordp301 · Post by **fordp301** » Tue Jun 30, 2009 8:45 pm

"application failed to initialize properly 0xc0000135. Click OK to terminate".

Any idea?

Edit: looks like I need to install .net framework, which apparently doesn't do well on a thin client ... more to follow.

I found this update Hope its help you download and install this

Code: Select all

http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=1809592&prodNameId=1809593&swEnvOID=1058&swLang=13&mode=2&taskId=135&swItem=vc-66762-1

[/code]

craigm1 · Post by **craigm1** » Tue Jun 30, 2009 9:28 pm

You need to keep a computer on but the sound quality on my pap2 is so much better, tried using 2 lines on one computer have 2 mj's but wouldn't work is this possible?? have 2 computers running the software so now I have 2 mj's on my pap2.

Christmas has come in June!!!!

Craig

oldtimercurt · Post by **oldtimercurt** » Tue Jun 30, 2009 9:31 pm

Came across this while looking into NET on thin client
http://forums11.itrc.hp.com/service/for ... sId=439748

Don't know how helpful but it does deal with NET 1.1

OTC

newtoncd · Post by **newtoncd** » Tue Jun 30, 2009 10:01 pm

fordp301 wrote:
"application failed to initialize properly 0xc0000135. Click OK to terminate".

Any idea?

Edit: looks like I need to install .net framework, which apparently doesn't do well on a thin client ... more to follow.
I found this update Hope its help you download and install this
Code: Select all
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=1809592&prodNameId=1809593&swEnvOID=1058&swLang=13&mode=2&taskId=135&swItem=vc-66762-1
[/code]

I got 1.1 installed and the program requires 2.0. Your link is for 2.0; good find, appreciate it. Unfortunately, my flash drive has only 61MB free (64MB capacity) and it requires the full flash drive to be empty to install. I will play around with it and see if I can get it to install.

roc1479 · Post by **roc1479** » Tue Jun 30, 2009 10:12 pm

Are you guys getting a ring on incoming calls using az1324's method?

synchron · Post by **synchron** » Tue Jun 30, 2009 11:36 pm

can someone specify settings for X-lite (something we can all test this with) before trying out on ATA?

I get 'Registration 408: Register Timeout with the following settings:

Please tell me what I did wrong:

Synchron

magicnick · Post by **magicnick** » Wed Jul 01, 2009 12:50 am

synchron wrote:can someone specify settings for X-lite (something we can all test this with) before trying out on ATA?

I get 'Registration 408: Register Timeout with the following settings:

Please tell me what I did wrong:

Synchron

address i think should be if onsame computer 127.0.0.1:5070

andsmith79 · Post by **andsmith79** » Wed Jul 01, 2009 12:59 am

Worked perfectly on my Linksys RTP300! Thanks for the interm fix!

Prior to following these instructions I tried all of the other suggestions everyone had on here...like setting the "Registration Expire" to 0. I forgot to change this back to 3600 which caused the first attempt to use the proxy to fail. Once I changed the registration to 3600 I was up and running.

BTW - Mapping 5070 to the machine running the proxy does not appear to be needed. I was able to make/receive calls with and without the mapping in my Smoothwall firewall...good deal!

UPNP is also not enabled on my firewall.

Next thing is to try the adding the 100k ohm resistor to the line to get caller id working.

So can anyone explain how this is actually working? I would RTFM...if there was an FM.

roc1479 · Post by **roc1479** » Wed Jul 01, 2009 9:05 am

andsmith79,

When you get an incoming call, does your phone ring? If so, which guide did you use to get your linksys working? I have the pap2 and before the magicjack update, the phone, a wired phone, worked well. After the upgrade and using the proxy method, the phone no longer rings on incoming calls.

I'm just wondering if I did something wrong or if it's the type of phone I'm using.

Thanks,

Guide_timothy · Post by **Guide_timothy** » Wed Jul 01, 2009 9:24 am

OMG OMG I followed the directions and it works

I am able to use my ATA with magic jack with that lil program thingy and running my computer and the best part is I dont have to use that stupid USB dongle which makes the calls nasty and snap crackles and pops now my calls are clear agian wooooooooooooo THANK YOU i was gonna shell out money for callcentric or sipgate (by the way on sipgate recieving calls is a bit hit or miss not everyone that called can get thru) my cheap low cost magic jack is working on my ATA Amen and god bless who ever made that program and for who ever posted the directions

xguju · Post by **xguju** » Wed Jul 01, 2009 9:57 am

this is sort of on topic, but for some weird reason I can't get the new SIP data out of my magicjack to try this out. Last time I used mjinfo, but it says that there is a parameter error. I tried using Stroth's sip grabber, but it just gives me a box with a text field. Any help on getting SIP data would be awesome as I Really want to use this!

roc1479 · Post by **roc1479** » Wed Jul 01, 2009 10:04 am

xguju,

Unplug your device and wait a min or so. Put it back in, make sure the softphone comes up and says ready, and use Stroths program to find the sip info again. It may take a try or 2, but it will work.

mel2000 · Post by **mel2000** » Wed Jul 01, 2009 11:21 am

Can someone please clarify 2 issues before I try MJMD5:

Does the MJMD5 program work with just about *any* Windows ATA?
Do I have to have my computer running 24/7 to make and receive calls, like the current MJ?

roc1479 · Post by **roc1479** » Wed Jul 01, 2009 11:26 am

It should work with any ATA, because you'll be using it as a proxy. It will require you to keep your pc on 24/7 because you'll be using the dongle to establish a connecting with MJ servers.

mel2000 · Post by **mel2000** » Wed Jul 01, 2009 12:26 pm

Thanks for the reply roc1479. I think I'll wait for a dongleless version that doesn't require 24/7 from my computer.

thisiskate · Post by **thisiskate** » Wed Jul 01, 2009 12:48 pm

Awesome...
It would be really nice if we can run this as a service.

synchron · Post by **synchron** » Wed Jul 01, 2009 1:14 pm

magicnick wrote: address i think should be if onsame computer 127.0.0.1:5070

Thanx magicnick - that did the trick!

Works good, although I don't understand why sometimes X-lite will still attempt to register and timeout (408) after immediately running/starting the MJMD5 service. But if I run the service and then wait like a minute and then run X-lite, registration will work. Incoming works great and I hear a good loud ring tone. Caller ID shows up too.

So for now, I have a good working MJ Softphone solution with much better echo cancellation than the lousy MJ S/W (when used without the dongle)as well as a decent DND feature that MJ took away. Surprisingly, I don't need a headset and can have a normal speakers/mic conversation.

I'll wait on the ATA until next month if this is still all working and MJ hasn't caught on.

Synchron

synchron · Post by **synchron** » Wed Jul 01, 2009 1:19 pm

thisiskate wrote:Awesome...
It would be really nice if we can run this as a service.

This CAN be run as a service. At least ala Firedaemon (which runs any windows EXE as a service). But once you configure it the 1st time and check 'Save Settings' you can just run it from startup folder, if that's what you want.

Synchron

roc1479 · Post by **roc1479** » Wed Jul 01, 2009 2:01 pm

Hmm,

I checked my pap2-na and it shows the following for incoming calls:

Call 1 State: Ringing
Call 1 Tone: Ring-Callback
Call 1 Encoder: G711u
Call 1 Decoder: G711u
Call 1 Type: Incoming

So it appears that it's trying to ring the phone, however, the phone doesn't ring. If I answer the phone while making a test call, it picks up.

Can it be the type of phone that I am using? It's an older handset, wired from ATT.

I also have my softphone set to headset.

Can't figure it out. I doubled checked my settings to no avail. Any suggestions? I just need the phone to ring when an incoming call comes it.

kingmony · Post by **kingmony** » Wed Jul 01, 2009 3:44 pm

has any one got this to work with asterisk?

grillovillegas · Post by **grillovillegas** » Wed Jul 01, 2009 4:58 pm

Its not working.....
tried with windows vista and xp...
registration failed ....

what else to change ?

the proxy is the ipmachine:5070 on the ata ...
but nothing

RonV · Post by **RonV** » Wed Jul 01, 2009 5:07 pm

kingmony wrote:has any one got this to work with asterisk?

Yes I have it working with asterisk. I did it first with the .NET code on a PC as the proxy then I used the source code provided in the other forum, compiled and have the proxy loaded locally on my asterisk box. So far I haven't had any problem with it.

grillovillegas · Post by **grillovillegas** » Wed Jul 01, 2009 5:12 pm

Its not working what i am doing bad......

My setup its on Proxy ...

but do i have to use Outbound Proxy ???? or What ?

desidude2000 · Post by **desidude2000** » Wed Jul 01, 2009 6:30 pm

this is great, but here's a suggestion. i have a hacked buffalo linkstation running linux. if we could run the proxy app on Linux instead of Windows that would be great. then i could use my linux thin client for this trick. any chance this would get ported to linux? even a simple command line proxy daemon would do. and if this is just a stright proxy trick, and squid be used?

tazxx · Post by **tazxx** » Wed Jul 01, 2009 7:35 pm

desidude2000 wrote:this is great, but here's a suggestion. i have a hacked buffalo linkstation running linux. if we could run the proxy app on Linux instead of Windows that would be great. then i could use my linux thin client for this trick. any chance this would get ported to linux? even a simple command line proxy daemon would do. and if this is just a stright proxy trick, and squid be used?

Check here http://www.phoneservicesupport.com/cert ... 74-90.html

thisiskate · Post by **thisiskate** » Wed Jul 01, 2009 9:40 pm

synchron wrote:
thisiskate wrote:Awesome...
It would be really nice if we can run this as a service.
This CAN be run as a service. At least ala Firedaemon (which runs any windows EXE as a service). But once you configure it the 1st time and check 'Save Settings' you can just run it from startup folder, if that's what you want.

Synchron

Firedaemon is a paid service. Even if I put it in the startup folder, I need to login right?

trek101 · Post by **trek101** » Wed Jul 01, 2009 11:04 pm

Downloaded app this morning and plugged in the information needed. It works great; now I am able to utilise my ATA again.

Wondering if there is a way to proxy another number on the same machine. Before I was utilising two numbers on one ATA until the 9th of June update. Just have to do more reading; definitely call quality has improved with the ATA and I am able to utilise my facsimile machine again. No more hit and miss on the dongle for now =)...

tazxx · Post by **tazxx** » Thu Jul 02, 2009 3:06 am

[quote="trek101"]That's my quarter's worth, but not enough to call someone who really cares at a pay telephone booth...quote]

let me know where YOU live, I havn't seen "pay Booth" in 10 years, and a quarter will get you a piece of bubble gum.

i'm thinking VM, but will it work?

golf/jetta · Post by **golf/jetta** » Thu Jul 02, 2009 7:07 am

incoming calls

don't know which ports
but if you turn on dmz it works.. atleast for me

Anon · Post by **Anon** » Thu Jul 02, 2009 8:00 am

Hi all,

Using the MJmd5 method I got my RTP300 running again! Yay!

But, I don't get an incoming ring. Did anyone figure what to do?

TIA!

roc1479 · Post by **roc1479** » Thu Jul 02, 2009 8:17 am

Anon,

I have the same exact issue with my Pap2-na. When the call comes in, I can see that it shows a status of incoming call in the log, however, the phone does not ring. If you do pick up the phone, does it also pick up the call?

What kind of phone are you using?

Anon · Post by **Anon** » Thu Jul 02, 2009 8:45 am

Well, I didn't do anything, but walk away from it for a while, now it rings! I wish everything worked out that way for me!

Sorry, but I can't tell you what happened or help since I didn't do anything.

Good Luck to you though, others have this issue. I'm sure someone will figure it out.

roc1479 · Post by **roc1479** » Thu Jul 02, 2009 8:59 am

Anon,

Lucky you man..lol I wish things were like that for you. Anyway, are you using a cordless or wired phone? If cordless, what brand are you using?

Thanks,

Anon · Post by **Anon** » Thu Jul 02, 2009 9:08 am

I am using a cordless phone. It's a cheapie one from Drugmart.

It's a 2.4 GHz made by COBY model CT-p8200

I think it cost $19.99. We liked it so much that we went back and bought another one!

roc1479 · Post by **roc1479** » Thu Jul 02, 2009 1:13 pm

Hah, figured it out. It was my wired phone all along. Switched to a Panasonic Cordless and the phone rang. I'm good to go.

Thanks,

synchron · Post by **synchron** » Thu Jul 02, 2009 1:20 pm

thisiskate wrote:
synchron wrote:
thisiskate wrote:Awesome...
It would be really nice if we can run this as a service.
This CAN be run as a service. At least ala Firedaemon (which runs any windows EXE as a service). But once you configure it the 1st time and check 'Save Settings' you can just run it from startup folder, if that's what you want.

Synchron
Firedaemon is a paid service. Even if I put it in the startup folder, I need to login right?

Firedaemon is a piece of software that you buy for ease and convenience. You can set it up to execute any Windows EXE as a service before you log on so that any multiuser account has it running already and your ATA phone should be registered with a dialtone already.

You really don't need it though, in this case, since there's a CLI version that can be run at startup as well.

Synchron

synchron · Post by **synchron** » Thu Jul 02, 2009 1:38 pm

Darn it, my Vonics/Sunrocket Innomedia ATA 6328Re won't register. Settings are:

Under Sip Proxy:

Sip Proxy: 127.0.0.1:5070
Use Outbound Proxy: Unchecked
Sip Local Signaling port: 5070 (this is usually 5060)
Sip Domain: 192.168.1.111 (router assigned computer IP)
Registration Expire Time: 60 (I've tried 3600, 1800, 360 as well).

Under User Account:

User Id: EXXXXXXXXXX01
Password: New 20 char MJ PW

The proxy/domain is the same thing I entered in the Xlite softphone which DOES work so I'm really scratching my head here, any clues?? (Obviously, the MJMD5 app is running in the background on the PC whose IP is 192.168.1.111)

TIA,

Synchron

Post by **laserjobs** » Thu Jul 02, 2009 2:03 pm

synchron wrote:Darn it, my Vonics/Sunrocket Innomedia ATA 6328Re won't register. Settings are:

Under Sip Proxy:

Sip Proxy: 127.0.0.1:5070
Use Outbound Proxy: Unchecked
Sip Local Signaling port: 5070 (this is usually 5060)
Sip Domain: 192.168.1.111 (router assigned computer IP)
Registration Expire Time: 60 (I've tried 3600, 1800, 360 as well).

Under User Account:

User Id: EXXXXXXXXXX01
Password: New 20 char MJ PW

The proxy/domain is the same thing I entered in the Xlite softphone which DOES work so I'm really scratching my head here, any clues?? (Obviously, the MJMD5 app is running in the background on the PC whose IP is 192.168.1.111)

TIA,

Synchron

Shouldn't the Sip Proxy be: 192.168.1.111:5070

synchron · Post by **synchron** » Thu Jul 02, 2009 2:36 pm

Well, if you look at page 2 of this thread, that's what I originally had set up with X-lite, that DIDN'T work. Magicnik corrected by using 127.0.0.1.

I would think it shouldn't make a difference, but apparently it does. There must be something else in the ATA that needs tweaking, or maybe it just won't work with Innomedia brand and only wants to work with Linksys.

Synchron

magicJack and magicJack Plus Support, Reviews, FAQs and Tricks

ATA Start Working with following setting

ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

Re: ATA Start Working with following setting

this works

Re: ATA Start Working with following setting

OMG OMG IT WORKS

does this work with asterisk

Re: does this work with asterisk

Yay! Sort of