ac-211-sr

[magicrocket]

Ok, I can't seem to get it to work. I've looked for some detailed directions but I can't seem to find any for this particular device.

I have my ac-211 unlocked, I have my SIP information but I can't seem to put the information in the right places to get my ATA to register on the magicjack network.

Login Information
ProxyUserName = EXXXXXXXXXX01
ProxyUserPassword = XXXXXXXXXXXXXXX

UDP Ports
SIPUDPDefaultPort = 0
SIPUDPPortRangeStart = 65535
SIPUDPPortRangeEnd = 49152

Other SIP Data
SIPCallerID = EXXXXXXXXXX01
UserDomain = talk4free.com
ProxyName = proxy1.columbus.talk4free.com
ProxyIP = 66.104.96.198
User-Agent = MagicJack/1.80.466c (SJ Labs)

what information goes where?

Here are my current settings:



Any help would be appreciated[/img]

[mberlant]

I only see two things that you should change. Other folks might see something I have missed.

1. At the top, under the Primary server IP address, set its hailing port to 5070.

2. Down at the bottom, set up your STUN client. For the STUN server address, I recommend 69.0.208.27 (stun.ekiga.net), and for the STUN server port, 3478.

There may be settings on other pages of your SR device manager, but I recommend trying it out with these changes. Don't forget to unplug your MJ from your PC before energizing your SR ATA.

[magicrocket]

That worked, thanks! And what's the odds of magicjack catching me using an ATA and turning off my service?

[mberlant]

Take your time to read through the various discussions, starting in this category. There is quite a bit of advice, but the biggest is to never plug in the MJ while the ATA is running.

[b3wh169]

The screen shots really help. Just what I was looking for. But I am still unable to get my AC-211N-SR to work. I think I still am struggling with the basics. My configuration is I have aa DSL modem set up in bridge mode. A wireless router connects to the PPoE & has my ISP username & password to log in to the ISP. I am not sure where to put the gizmo in this chain. Also not sure about Autoconfig and other WAN & LAN Settings. Sorry for all the basic questions.

[msiam]

I assume that your modem, router and PC are in the chain so far, and all of it works fine..The Way SunRocket had it set up was to come out of the modem LAN to the WAN of the gizmo out of LAN of Gizmo to internet of the router, if it all is set up in that chain, it should be fine, sometimes you can just come out of one of the spare ports of the router into the Wan of the gizmo and not worry about the Gizmos LAN, you should have success with that. Let us know how that turns out, As mberlant says, "never plug in the MJ while the ATA is running." Have fun and Im sure glad you have found the correct Thread
msiam

In re reading your post, I have a suspicion that your ISPs credentials are not in your modem, they are in your PC and you have to log in each time that you want to get on the internet, if this is the case, you will have to contact your ISP and tell them that you want to move those credentials to your DSL Modem so as the MODEM is always connected to the internet.tell them that you want the wireless Router always available. If your ready lite or voip lite is not on, I am thinking this could remedy your problem, It did in two cases I am aware of..

[b3wh169]

I believe my ISP credentials (PPP?) are in my Router. I do not need to log in everytime. Ready light is on, but phone line light is not on, and I don't have any dial tone.

[royroy]

I AM NOT ABLE TOGET DIAL TONE. CAN ANY ONE HELP?
Here is my Settings for:
SunRocket Gizmo AC-211-SR
VoIP Gageway
I. Home - System Information
A. Module Type = 211
B. Interfaces = 2ports FXS Phone
2ports 10/100Base-T/TX
C. System Uptime = 0 days, 5h 33m23s
D. System Real Time =
E. Security = Password installed
F. Application Code Version = SIP version 4.57 US (APP 41x)
G, Downloader Code Version = 4.57 US (LDR 41)
H. CPU Hw Version = 20
II. WAN
A. WAN Status - Network Settings
1. Dynamic IP Assignment = NO
2. DHCP lease remaining = 3 days, 16h 41m 18s
3. IP Address = 216.234.64.8
4. MAC Address = 00:a0:12:24:03:eb
5. Subnet Mask = 255.255.255.0
6. Default Gateway = 216.254.71.1
7. DNS Address 1 = 0.0.0.0
8. DNS Address 2 =
9. DNS Address 3 =
10. DNS Address 4 =
11. Domain Name =
12. Broadcast Rate = 100% (of downstream bit rate)
13. Multicast Rate = 100% (of downstream bit rate)
B. WAN Settings
1. Obtain WAN Configuration dynamically = NOTSELECTED
2. Specify fixed WAN Configuration = SELECTED
a. IP Address = 216.234.64.8
b. IP Netmask = 255.255.255.0
c. IP Gateway = 216.254.71.1
d. IP DNS Server 1 =
e. IP DNS Server 2 =
f. Host Name =
g. Domain Name =
h. MTU = 1500
3. Multicast Rates
a. Broadcast Rate = 100 % (of Ethernet connedtion bitrate)
b. Multicast Rate = 100 % (of Ethernet connedtion bitrate)
C. PPPoE - WAN PPPoE Configuration
1. Enable PPPoe = NO
2. Authentication
a. User Name =
b. Password =
3. Settings
a. Idle Timeout =
b. Service Name =
c. AC Name =
D. PPTP - PPPT Configuration
1. Enable PPPT = NO
2. Authentication
a. User Name =
b. Password =
3. Settings
b. Service Address =
E. MAC Spooling - MAC Spooling Configuration
1. WAN MAC Address =
2. Learn MAC = 001B24FF1A0E
F. AutoConfiguration - Auto Configuration
1. Enable Automatic Configuration = NOT SELECTED
2. Automatic Configure ID = always
3. Use DHCP code options 66,67 = NOT SELECTED
4. Polling time (hours) = 24
5. Server protocol = HTTP
6. Server Address = 67.133.234.53
7. File name = gms/AC-211/B/ipg_211_00a0122403eb.cfg
III. LAN
A. LAN Settings - LAN Configuration
1. Network Settings
a. IP Address = 192.168.251.1
b. Subnet Mask = 255.255.255.0
2. Multicast Rates
a. Broadcast Rate = 100 % (of Ethernet connection bitrate)
a. Multicast Rate = 100 % (of Ethernet connection bitrate)
3. Rate Control
a. Disable Rate Limits = SELECTED
b. Dynamic Rate Limits = NOT SELECTED
- User Upload Rate (Kbps) = 32
- Current LAN Rate Limit (Kbps) =
c. Fixed Rate Limits = NOT SELECTED
- LAN Rate Limit(Kbps) = 32
B. DHCP - DHCP Server Configuration
1. Server Settings
a. Enabled = NOT SELECTED Disabled = SELECTED
b. Client IP Address Range: 192.168.251. = 100.123
c. Scan network for given leases upon reboot = Yes
2. Client Network Information
a. Domain Name =
b. DNS Server 1 =
c. DNS Server 2 =
d. Default Lease Time = 86400 seconds
3. Static Address Assignments
a. Identify Using = Hostname
b. Host Identifier =
c. Internet Address: 192.168.251. =
C. Port Forwarding - Port Forwarding Configuration
1. Reserved Ports
a. The following ports have been reserved by the CPE,
and may not be forwarded to the LAN
68, 16384-16399, 5060
2. Port Forwarding to LAN
a. Port Range =
b. Protocal = Both
c. Destination Address 192.168.251. =
3. Demilitarized Zone
a. Demilitarized Zone Server IP: 192.168.251. =
D. NAT - NAT IPSec traverse configuration
1. Enable NAT IPSec traverse = NOT SELECTED
IV. Security
A. Password - Set Security Administrator Password
1. Password is currently installed
2. New password =
3. Confirm new password =
B. Advanced - Advanced Security Configuration
1. Advanced Security Enable = NOT SELECTED
a. DHCP Security Enabled = NOT SELECTED
b. IP Address (8 empty input boxes)
c. Subnet mask (8 empty input boxes)
C. Access - Service Access Configuration
1. Select which interfaces are allowed access to the services listed below
2. Telenet
a. LAN = NOT SELECTED
b. WAN = NOT SELECTED
3. HTTP Admin Access
a. LAN = SELECTED
b. WAN = NOT SELECTED
4. Enable user access on LAN
5. Enable User Mode = SELECTED
D. Encryption - Set Encryption Key
1. Encryption key is currently installed
2. New Key =
3. Confirm new key =
E. EncGeneral - Set General Configuration File Encryption Key
1. No Encryption key installed
2. New key =
3. Confirm new key =
V. SIP
A. SIP - SIP Configuration
1. SIP Server Settings
a. Primary server
- IP Address = 67.106.133.198:5070
- Port = 5060
- Domain Name* = proxy1.newark.talk4free.com
b. Send Registration Request = SELECTED
2. Gateway Settings
a. Dial Plan = (>#|911|611|411|311|00|0T|[2-9]xxxxxxxxx|1[2-9]xxxxxxxxx|[2- 9]xxxxxxT|011[2-9]x.T|*x.T)
b. Transport = UDP
c. Enable T.38 fax support NOT SELECTED
d. Line1
- User / Phone Num = E201XXXXXXX01
- CallerID Name = MJ
- Port* = 5060
- AEC On = ON
- Authentication User Name = E201XXXXXXX01
- - Password = XXXXXXXXXXXXXXXXXXXX
e. Line2
- User / Phone Num =
- CallerID Name =
- Port* = 5061
- AEC On = ON
- Authentication User Name =
- Password =
3. NAT Settings
a. NAT IP Address =
b. RTP/RTCP Port Base = 16384
4. STUN Server Settings
a. STUN server IP Address = 69.0.208.27
b. STUN server Port =3478
B. SIP Extensions
1. Support PRACK method with provisional response reliability = NOT SELECTED
2. Encode SIP URI with user parameter = NOT SELECTED
3. INVITE Expires Timer value (sec) = 9999
4. SIP Session Timer value (sec) =
5. SIP Registration Timer value (sec) = NOT SELECTED
6. Send RTP on 183 Session Progress = SELECTED
C. Line1 - Line Status
1. Registration status - Registration state: Not registered
2. OOB RTP Telephone Event Signalling
a. Send Out-Of-Band Telephone Events = None
b. RFC2833 signalling using payload value =
c. Suppress voice packets during RFC2833
Telephone Event packet transmission = NOT SELECTED
d. Squelch inband DTMF audio = NOT SELECTED
- ABCD event signalling mode = Transition
e. Play DTMF received via RFC2833 = NOT SELECTED
f. Play DTMF received via SIP INFO = NOT SELECTED
3. Call Forward Configuration
a. Call forward = Disabled
4. Gain Control Configuration
a. Line (input) gain = -3
b. Headset (output) gain = -3
D. Line2 - Line Status
1. Registration status - Registration state: Not registered
2. OOB RTP Telephone Event Signalling
a. Send Out-Of-Band Telephone Events = NOT SELECTED
b. RFC2833 signalling using payload value = NOT SELECTED
c. Suppress voice packets during RFC2833 NOT SELECTED
Telephone Event packet transmission = NOT SELECTED
d. Squelch inband DTMF audio = NOT SELECTED
- ABCD event signalling mode = Transition
e. Play DTMF received via RFC2833 = NOT SELECTED
f. Play DTMF received via SIP INFO = NOT SELECTED
3. Call Forward Configuration
a. Call forward = Disabled
4. Gain Control Configuration
a. Line (input) gain = -3
b. Headset (output) gain = -3
VI. CODECS - Audio/CODEC Configuration
A. CODECS - Selected
1. G711U
a. Packetization = 20ms
b. Silence Suppression = OFF
2. G711A
a. Packetization = 20ms
b. Silence Suppression = OFF
3. G723 (this has a select box = NOT SELECTED)
a. Packetization = 30ms (no option to change)
b. Silence Suppression = ON
4. G726 (this has a select box = NOT SELECTED)
a. Packetization = 30ms
b. Silence Suppression = ON
5. G729 (this has a select box = NOT SELECTED)
a. Packetization = 20ms
b. Silence Suppression = OFF
B. Force preferred CODEC
1. Line 1 - preferred CODEC = NONE
2. Line 2 - preferred CODEC = NONE
3. FAX preferred CODEC = G711U
C. Jitter Buffer
1. Adaptive Jitter Buffer = SELECTED = 100ms
(maximum playout delay in milliseconds)
2. Fixed Jitter Buffer = NOT SELECTED = 80ms
(fixed playout delay in milliseconds)
VII. Miscellaneous
A. Clock
1. NTP Server = 67.133.234.55
2. Time Zone = GMT-05:00 Eastern Time
3. Adjust clock for daylight savings = NOT SELECTED
B. Local - Local settings
1. Caller ID
a. Country = United States
2. Ring Format
a. Trapezoid 20Hz Balanced = SELECTED
b. Sinusoid 25Hz Balanced = NOT SELECTED
C. Syslog - Syslog daemon address configuration
1. Syslog Server Address
2. Message severity level = 3 Error
3. Send device information to syslog daemon
4. Start Upload Entry =
5. Select Line Number = all
D. Protocol Ports - Ports configuration
1. HTTP server configuration - HTTP Server Port = 80
2. Telnet server configuration - Telnet Server Port =
3. Syslog client configuration - Syslog Client Port =
4. TFTP client configuration - TFTP Client Port =
5. HTTP client configuration - HTTP Client Port =
E. Calling - Advanced Calling features
1. Advanced calling features configuration
a. Enable Call Waiting = SELECTED
- Show Caller Identity on Call Waiting = SELECTED
b. Enable Caller ID display = SELECTED
c. Enable 3-way calling = SELECTED
d. Enable last call redial = NOT SELECTED
e. Enable distinctive ringtones = SELECTED
f. Enable call transfer = NOT SELECTED
g. Enable Do Not Disturb (DND) = NOT SELECTED
h. Enable call forwarding = NOT SELECTED
i. Enable block/accept last call = NOT SELECTED
j. Enable auto redial = NOT SELECTED
- Auto redial Expire Timer value (sec) = 1800
k. Enable Block Caller ID = NOT SELECTED
l. Enable Anonymous Call Rejection (ACR) = NOT SELECTED
2. Handset advanced configuration - Assigned Key Patterns
a. Conditional forward = *1
b. Unconditional forward = *2
c. Disable forward = *3
d. Enable DND = *4
e. Disable DND = *5
f. Transfer = *98
g. Redial last call = *69
h. Block last call = *60
i. Accept last call = *80
j. Auto redial = *66
k. Disable auto redial = *86
l. Block Caller ID (per call) = *70
m. Enable anonymous call rejection (ACR) = *77
n. Disable anonymous call rejection (ACR) = *87
3. Dead-air configuration - Dead-air period configuration
a. Duration (sec) = 10
F. Ring tones - Ringing Configuration
1. Ring Names - Ring Name 1 - 8 (all blank)
2. Ring Cadences - Ring Cadence 1 - 8 (all blank)
3. Call Waiting Tone Cadences
CWT Cadence 1 - 8 (all blank)
4. Call Progress Tones
a. Dial Tone =
b. Busy Tone =
c. Reorder Tone =
d. Offhook Warning =
e. Ringback Tone =
f. Confirm Tone =
g. Stutter Tone =
h. Ring =
i. Hold Tone =
VIII. Services - Voice & Management Services Configuration
A. WAN Management / All VLAN Tag = 1
B. WAN Priority Tag =
C. VLAN Tag for RTP packets =
D. Priority Tag for RTP packets =
E. TOS for RTP packets =
F. VLAN Tag for Call Signalling packets =
G. Priority Tag for Call Signalling packets =
H. TOS for Call Signalling packets =
IX. VLAN - VLAN Configuration
A. VLAN Enable = NOT SELECTED
B. VLAN (spread sheet - only the first line is filled out)
Port
1 - 2
VLAM - Default - 1 - 1
1 - U - U
X. Download
XI Reset
XII. Log out

[mufon]

Your original screenshot was the most useful, as mentioned before the port field should be "5070".

Your config looks more like something that works on a pap2. Don't use the ":5070" appended to your proxy address. Use 5070 in the port field and it should work. Don't forget on an ac-211 you must do a full reset after changing sip creds.

Try using "stratus.com" in the domain field, although I don't think it matters.

[rgoo2]

So for the Sunrocket AC211, there is no spot to put in the User Agent:
MagicJack/1.80.466c (SJ Labs) ?

[b3wh169]

I was able to get my AC-211N-SR working, and it seemed to do just fine plugging into my router. I can't remember what made the difference, other than perhaps just powering down the ATA and trying it again after checking all the fields to ensure I had entered the info correctly.

I also had a SPA-2102 from another old SR account. I am currently using that ATA, as it seems to give more configuration options and better call quality.

Thanks for the help.

[smaye]

The key word is 'HAD'.

About a year or so ago I got my AC211SR converted and working for my MJ service. I decided not to use MJ at all until they had number porting. Still not happening.

Now I have gotten over keeping my local number so I can start using MJ again. My MJ device works fine on my Win7 PC, but would prefer to use my AC211SR Gizmo. I plugged it in hoping it would work like it did before but, NO Cigar.

I tried to log in to the AC211SR, but now my Authenticate password is not working.

Can someone please give me some pointers?

[VaHam]

The key word is 'HAD'.

About a year or so ago I got my AC211SR converted and working for my MJ service. I decided not to use MJ at all until they had number porting. Still not happening.

Now I have gotten over keeping my local number so I can start using MJ again. My MJ device works fine on my Win7 PC, but would prefer to use my AC211SR Gizmo. I plugged it in hoping it would work like it did before but, NO Cigar.

I tried to log in to the AC211SR, but now my Authenticate password is not working.

Can someone please give me some pointers?

Try searching here for MJMDM5 proxy!

[smaye]

Try searching here for MJMDM5 proxy!

Will do. Thanks for the tip!