pap2 ver2 config help

oxigenado · Post by **oxigenado** » Mon Jun 09, 2008 12:28 pm

Could some 1 plz assist me with this particular device?

settings are as follow:

Line 1
Caller ID Number:E801741017301
Username:E801741017301
Password:my20digitspasswd
Proxy Server:proxy1.SaltLakeCity.talk4free.com port:5070
Registrar Address:proxy1.SaltLakeCity.talk4free.com port:5070
Digital map:*xxT|*1xx|[349]11|1xxx[2-9]xxxxxx|[2-9]xxxxxxT|[2-9]xxxxxxxxx|011x.T

(caller id/username are fake for obvious reasons)

Provisioning is set to OFF

This pap2v2 was fonage, is unlocked, but but the provision info still shows the carrier server info and stuff, thats why I turned off provisioning. I followed instructions on how to get the encrypted xml, and done it successfully, but the line just wont register.

It shows this: Registration Status : *801741017301 E801741017301 Proceeding

Any ideas?

Thank you

Stewart · Post by **Stewart** » Mon Jun 09, 2008 1:19 pm

There is an issue with PAP2 V2 where the firmware does not allow alphabetic characters in the caller ID field. You can see that the initial E is getting changed to *. I had heard that this was fixed in newer firmware, but can't find the link now. If you Google pap2v2 alphanumeric, you'll see various posts about this issue; with luck you'll find a link to a solution.

oxigenado · Post by **oxigenado** » Mon Jun 09, 2008 2:27 pm

Stewart wrote:There is an issue with PAP2 V2 where the firmware does not allow alphabetic characters in the caller ID field. You can see that the initial E is getting changed to *. I had heard that this was fixed in newer firmware, but can't find the link now. If you Google pap2v2 alphanumeric, you'll see various posts about this issue; with luck you'll find a link to a solution.

Yes, I did hear about it, but some posted that the the 1.00.13 firware was responsible for that, and thats why im running 1.00.16, but like you mentioned, it does shows a * instead of the E, I guess I will try the 1.00.22 fw

thx

onlinepcfun · Post by **onlinepcfun** » Mon Jun 09, 2008 2:42 pm

Hey I had same troubles with 1.00.16

Try to get modified RTP300 firmware on it http://www.phoneservicesupport.com/post ... ght=#12863 (you just have get hold of a linux box and create urself http://www.dslreports.com/forum/r19868031- )

That solves the alpha issue

Heard that 1.00.22 has someway of locking back to vonage again...by going with RTP300 option you are even covered with accidental resets

oxigenado wrote:
Stewart wrote:There is an issue with PAP2 V2 where the firmware does not allow alphabetic characters in the caller ID field. You can see that the initial E is getting changed to *. I had heard that this was fixed in newer firmware, but can't find the link now. If you Google pap2v2 alphanumeric, you'll see various posts about this issue; with luck you'll find a link to a solution.
Yes, I did hear about it, but some posted that the the 1.00.13 firware was responsible for that, and thats why im running 1.00.16, but like you mentioned, it does shows a * instead of the E, I guess I will try the 1.00.22 fw

thx

oxigenado · Post by **oxigenado** » Mon Jun 09, 2008 3:38 pm

Is there an easier way? like upload the firmware and hook it up? Im not very good with linux, Im afraid to fry the thing, I would need very detail instructions, but I'll see if I fidn the courage to do it.

Thx

onlinepcfun wrote:Hey I had same troubles with 1.00.16

Try to get modified RTP300 firmware on it http://www.phoneservicesupport.com/post ... ght=#12863 (you just have get hold of a linux box and create urself http://www.dslreports.com/forum/r19868031- )

That solves the alpha issue

Heard that 1.00.22 has someway of locking back to vonage again...by going with RTP300 option you are even covered with accidental resets

oxigenado wrote:
Stewart wrote:There is an issue with PAP2 V2 where the firmware does not allow alphabetic characters in the caller ID field. You can see that the initial E is getting changed to *. I had heard that this was fixed in newer firmware, but can't find the link now. If you Google pap2v2 alphanumeric, you'll see various posts about this issue; with luck you'll find a link to a solution.
Yes, I did hear about it, but some posted that the the 1.00.13 firware was responsible for that, and thats why im running 1.00.16, but like you mentioned, it does shows a * instead of the E, I guess I will try the 1.00.22 fw

thx

onlinepcfun · Post by **onlinepcfun** » Mon Jun 09, 2008 5:07 pm

Me too...not too good with linux - just followed steps and ran a script and got the patched firmware...If I can do it I think anybody can do it - I just had this in thoughts - if it fries I will get a paper weight otherwise I will get a $50 worth of totally unlocked ATA that I can use it anywhere and steps look very simple...

Just to clarify - no special cables required...once you got the patched firmware you will be uploading via the web interface like you did in other steps

Download RTP300's 3.1.24 firmware from linksys website...
Download file from dslreports link (I used winrar to unpack it)
Put both of them in same directory (original RTP300 firmware goes in to the root - NOT source)
Run .sh script on the root (This is the only place you need linux for! - make sure you have permissions to execute all files in pap2patcherplus.tar.bz2)
Copy the img.web file you got to your PC - rename to .img (not sure if it is a must) - upload as usual

If you got the file sizes and no messages/warnings when executing script, then I would say you don't have to worry at all

Hope I gave a little courage to do it! - GOOD LUCK

Sorry I won't be able to do these for you and upload firmware

oxigenado wrote:Is there an easier way? like upload the firmware and hook it up? Im not very good with linux, Im afraid to fry the thing, I would need very detail instructions, but I'll see if I fidn the courage to do it.

Thx

oxigenado · Post by **oxigenado** » Wed Jun 11, 2008 2:14 am

Well. I manage to do it. apparently everything went ok, got the file, rename it to .img, uploaded without a problem, restarted, but then the device is not taking an ip address, its stuck with the 192.168.15.1 set my ip to 192.168.15.100 and I cant reach it at all, the power and lan lights on the pap2 are solid, even unplugging the network cable, any suggestions?

Thank you.

onlinepcfun wrote:Me too...not too good with linux - just followed steps and ran a script and got the patched firmware...If I can do it I think anybody can do it - I just had this in thoughts - if it fries I will get a paper weight otherwise I will get a $50 worth of totally unlocked ATA that I can use it anywhere and steps look very simple...

Just to clarify - no special cables required...once you got the patched firmware you will be uploading via the web interface like you did in other steps

Download RTP300's 3.1.24 firmware from linksys website...
Download file from dslreports link (I used winrar to unpack it)
Put both of them in same directory (original RTP300 firmware goes in to the root - NOT source)
Run .sh script on the root (This is the only place you need linux for! - make sure you have permissions to execute all files in pap2patcherplus.tar.bz2)
Copy the img.web file you got to your PC - rename to .img (not sure if it is a must) - upload as usual

If you got the file sizes and no messages/warnings when executing script, then I would say you don't have to worry at all

Hope I gave a little courage to do it! - GOOD LUCK

Sorry I won't be able to do these for you and upload firmware

oxigenado wrote:Is there an easier way? like upload the firmware and hook it up? Im not very good with linux, Im afraid to fry the thing, I would need very detail instructions, but I'll see if I fidn the courage to do it.

Thx

onlinepcfun · Post by **onlinepcfun** » Thu Jun 12, 2008 2:12 pm

Yep. it is because of some firmware issue...it has default ip address of 192.168.15.1 - see this thread - http://www.dslreports.com/forum/r19873802-
If you put this behind router and then try to access it thru that IP
This is the thread where this is covered...http://www.dslreports.com/forum/remark,16514227 - read from 28th page onwards and look for answers

Keep it on static ip under the same subnet as your router should keep this up and running all the time - looks like this has some issues with dynamic address

Sorry forgot to tell you about it! - anyway you did the big step and I am sure you will be a happy fellow sooooooooooooon.

oxigenado wrote:Well. I manage to do it. apparently everything went ok, got the file, rename it to .img, uploaded without a problem, restarted, but then the device is not taking an ip address, its stuck with the 192.168.15.1 set my ip to 192.168.15.100 and I cant reach it at all, the power and lan lights on the pap2 are solid, even unplugging the network cable, any suggestions?

Thank you.

oxigenado · Post by **oxigenado** » Fri Jun 13, 2008 1:12 pm

I dont know what Im doing wrong here. I hard reset it holding the reset button for 8 secs, the ip does change to 192.168.1.254, I was able to get in the config pages, set it to dhcp, and it doesnt seem to get an, I chech my router is it assings and IP address but it wont let me get into the config pages again. Tried to set a static ip, and nothing. So, this is what I did so the pap kept the config:

-Hard reset so I can access it thru the 192.168.1.254 ip address

-Configured line one, proxy address, username, passwd, port 5070, cid (is there anything else that need to be configure? how about register, is yes as default)

-The unit restarts, and keeps all config info, and then I input the static ip (192.168.2.141), along with my isp dns and the router ip address as the gateway (192.168.2.1)

After this Im able to access the web interface with the specified IP, but the unit doesn't seem to connect, phone 1 light never come up, I ping a few sites from the papa, and it does sees www.yahoo.com and other, including my router, obviously.

Any suggestions? Am I doing something wrong? Is there other configuration that Im not doing? what are your setting on your pap2v2 for magicjack?

Thanks in advance!

onlinepcfun wrote:Yep. it is because of some firmware issue...it has default ip address of 192.168.15.1 - see this thread - http://www.dslreports.com/forum/r19873802-
If you put this behind router and then try to access it thru that IP
This is the thread where this is covered...http://www.dslreports.com/forum/remark,16514227 - read from 28th page onwards and look for answers

Keep it on static ip under the same subnet as your router should keep this up and running all the time - looks like this has some issues with dynamic address

Sorry forgot to tell you about it! - anyway you did the big step and I am sure you will be a happy fellow sooooooooooooon.

oxigenado wrote:Well. I manage to do it. apparently everything went ok, got the file, rename it to .img, uploaded without a problem, restarted, but then the device is not taking an ip address, its stuck with the 192.168.15.1 set my ip to 192.168.15.100 and I cant reach it at all, the power and lan lights on the pap2 are solid, even unplugging the network cable, any suggestions?

Thank you.

Stewart · Post by **Stewart** » Fri Jun 13, 2008 2:26 pm

What does Registration Status show? Any other useful status values?

I know almost nothing about the PAP2 V2, but virtually all VoIP devices have 'debug' or 'syslog' features that can send copies of SIP requests and responses to your PC. You want to find out if REGISTER requests are going out and what responses, if any, are coming in. Alternatively, you could capture the device's traffic with Wireshark directly, if you have some means of getting the PC to "see" the packets (dumb hub, managed switch, PC with two NICs, etc.)

oxigenado · Post by **oxigenado** » Fri Jun 13, 2008 6:06 pm

It only shows, registration status: failed

Stewart wrote:What does Registration Status show? Any other useful status values?

I know almost nothing about the PAP2 V2, but virtually all VoIP devices have 'debug' or 'syslog' features that can send copies of SIP requests and responses to your PC. You want to find out if REGISTER requests are going out and what responses, if any, are coming in. Alternatively, you could capture the device's traffic with Wireshark directly, if you have some means of getting the PC to "see" the packets (dumb hub, managed switch, PC with two NICs, etc.)

oxigenado · Post by **oxigenado** » Fri Jun 13, 2008 11:36 pm

Nevermind, I've got it!!! Reset to defaults and just use usrname:passwd, proxyname:5070, nat:off, registration:on outbound proxy sames as the proxy, works like a charm!!!

Thank for ure help brothat, Im a happy camper now.

oxigenado wrote:It only shows, registration status: failed

Stewart wrote:What does Registration Status show? Any other useful status values?

I know almost nothing about the PAP2 V2, but virtually all VoIP devices have 'debug' or 'syslog' features that can send copies of SIP requests and responses to your PC. You want to find out if REGISTER requests are going out and what responses, if any, are coming in. Alternatively, you could capture the device's traffic with Wireshark directly, if you have some means of getting the PC to "see" the packets (dumb hub, managed switch, PC with two NICs, etc.)

cyberma007 · Post by **cyberma007** » Wed Mar 18, 2009 11:10 pm

Thanks for you post guys, you are life saver, i looked for info for over 2 days, and finaly found your posts,
I got everything going i can call both in and out, but miner problem is i have to hit # sign for my number to go throgh, and recived call, stops comming if phone everything is idle for more then 15-30 min and goes to voicemail with MJ.
Any Idea?

mberlant · Post by **mberlant** » Thu Mar 19, 2009 12:19 am

You need to do two things more. For the outgoing delay problem, use the Search button to look for "dial plan" from me. That will give you just what I think you need. For the inbound, you need to set your "Register Expires" timer to not more than 840 seconds. Search for "Register Expires" for the background information on this requirement.

And, congratulations on getting your PAP2 working.

cyberma007 · Post by **cyberma007** » Thu Mar 19, 2009 12:27 am

Thanks you guys are the best, I am really Happy
In my PAP2 with RTP300 Firmware now , i dont see any DailPlan option.

mberlant · Post by **mberlant** » Thu Mar 19, 2009 12:29 am

Read the thread I mentioned. It will tell you what to put in the box at the bottom of your Line page.

cyberma007 · Post by **cyberma007** » Thu Mar 19, 2009 12:48 am

mberlant
Can you please point me to where it is, I feal stupid, but i cant find it, it looks like you are a GUD here and have a ton of post so it is hard to find it.
Thanks

mberlant · Post by **mberlant** » Thu Mar 19, 2009 3:31 am

It's the fifth thread in the Search I asked you to do. This is it.

cyberma007 · Post by **cyberma007** » Thu Mar 19, 2009 11:19 am

But it looks like they have removed the Dial Plan option in this firmware that is made for PAP2 V2 running RTP300.
I dont see anywhere in there to change it, does anyone know anywhere else in this firmware to change it?
Thanks

cyberma007 · Post by **cyberma007** » Fri Mar 20, 2009 12:09 am

mberlant
Thanks a Ton
it works now
how do i allow international out
This is what i have not from you told me.

([1235-8]11!|[49]11S0|<:1818>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0| 1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!|011!)

mberlant · Post by **mberlant** » Fri Mar 20, 2009 8:04 am

You don't mention if you want to be able to call just a couple of favorite countries or if you want to allow anyone to use your MJ to call anywhere in the world (including destinations that cost several dollars per minute). I will assume that you have a favorite country in mind and that it is not within Country Code 1.

The safest way to add one or two countries to the "permitted" destinations list is to add a new phrase to the Dial Plan for each of these countries. Make a phrase in the form of "011???xxx.|", where ??? is replaced by the Country Code of your choice, and add it before the 1441!| entry in the Dial Plan. For example, if you want to add France you would insert 01133xxx.| into your Dial Plan. Do this for each individual country you wish to add.

cyberma007 · Post by **cyberma007** » Sat Mar 21, 2009 2:12 pm

Thanks for your help you are the greatest.

cyberma007 · Post by **cyberma007** » Sun Mar 22, 2009 11:22 pm

Mberland
I added this dail plan in order to call sweden, but I get busy signal when i call 011

([1235-8]11!|[49]11S0|<:1818>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0|01146xxx.|1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!|011!)

What am I doing wrong , I followed your advice

mberlant · Post by **mberlant** » Mon Mar 23, 2009 3:23 am

The element 01146xxx., being more specific and earlier in the Dial Plan, should be overriding the 011! element at the end of the Dial Plan. I guess you'll need to take out the |011! to make it work. Jag är ledsen för förvirring.

cyberma007 · Post by **cyberma007** » Mon Mar 23, 2009 10:40 am

Mberlant

oowwwoo That is freaky

Hur viste du att jag pratar svenska?

cyberma007 · Post by **cyberma007** » Mon Mar 23, 2009 10:43 am

ooopps
I just got it, I asked you how to call sweden.
That is funny
Bone head Bone head Bone head.

Tack sa mycket.

cyberma007 · Post by **cyberma007** » Tue Mar 24, 2009 7:46 pm

Mberlant

I removed what you told me at now i dont get busy signal, but i also dont get any result, almost like i have not finished dailing,
it is dead air when i finish dailing the number
([1235-8]11!|[49]11S0|<:1818>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0|01146xxx.|1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!)

mberlant · Post by **mberlant** » Tue Mar 24, 2009 8:54 pm

If you are not doing so already, try putting a # at the end of your dialed number. Also, make sure that there is enough money in your deposit account to cover the cost of the phone call.

p0tsm0ke · Post by **p0tsm0ke** » Fri Mar 27, 2009 3:42 am

i got pap2 working and a pap2 v2 working

i have my pap2 flashed with sipura
i have my pap2 v2 flashed with RT300 PATCH

looking to find out about a DLINK VTA VR i have that but its the same problem as the PAP V2 gives * in front of the USER

anyone know about this

p0tsm0ke · Post by **p0tsm0ke** » Sat Mar 28, 2009 1:51 am

this is a how to flash the pap2 v2 adapter with out a problem

1.) go to : http://www.ubuntu.com/ <-- download the iso and burn it to a disc
2.) download pap2patcherplus.tar.bz2
3.) download rtp300_fw_3.1.24_US.img
4.) place those 2 files in a folder on your C drive name the folder LINKSYSMOD
4.) boot your disc you burned
5.) when your disc boots. go to C drive and then to LINKSYSMOD right click on pap2patcherplus.tar.bz2 click extract this makes a pap2patcherplus folder
6.) copy rtp300_fw_3.1.24_US.img in to the pap2patcherplus folder
7.) go in to pap2patcherplus and double click patch-apply.sh
8.) wait about 1 min and you should have 2 files pap2v2_fw_3.1.24_NA.img.web , pap2v2_fw_3.1.24_NA.img.flash
9.) rename pap2v2_fw_3.1.24_NA.img.web to pap2v2_fw_3.1.24_NA.img
10.) go to this link : http://192.168.X.XXX/cgi-bin/firmwarecfg you will be prompted for a user/pass : Admin / Admin or Admin /
11.) once your in that page go to : http://192.168.X.XXX/upgrade select your pap2v2_fw_3.1.24_NA.img wait for it to flash once done the pap2 will reboot
12.) you need to set your router to 192.168.1.1 because the pap2 v2 is now set as http://192.168.1.254 after that you can set your pap2 up with your new firmware
13.) enter all your magicjack info and click save. on the info screen you will see FAILED. this is ok click ADVANCED and then factory reset only the device not the provision state after it reboots you should be good to go.

^^^ i hope this guide helps out the people that need help with the pap2 v2 because it was a pain in the A$$ compared to the pap2 v1 ^^^

** after you flash with this firmware no commands on the phone will work. the default ip is 192.168.1.254 keep that in mind. you will need a hub or router or switch to talk to the device no direct connection will work ***

seti007 · Post by **seti007** » Sat Mar 28, 2009 3:38 am

P0tsm0ke, thats an amazingly helpful post . I cant thank you enuf. I do have a couple of Qs.
1. Which version of firmware should i start with on the pap2?
2. On step 12 do i use the same login and pass as before ie Admin/Admin?
Thanks a lot for writing the step by step.

p0tsm0ke wrote:this is a how to flash the pap2 v2 adapter with out a problem

1.) go to : http://www.ubuntu.com/ <-- download the iso and burn it to a disc
2.) download pap2patcherplus.tar.bz2
3.) download rtp300_fw_3.1.24_US.img
4.) place those 2 files in a folder on your C drive name the folder LINKSYSMOD
4.) boot your disc you burned
5.) when your disc boots. go to C drive and then to LINKSYSMOD right click on pap2patcherplus.tar.bz2 click extract this makes a pap2patcherplus folder
6.) copy rtp300_fw_3.1.24_US.img in to the pap2patcherplus folder
7.) go in to pap2patcherplus and double click patch-apply.sh
8.) wait about 1 min and you should have 2 files pap2v2_fw_3.1.24_NA.img.web , pap2v2_fw_3.1.24_NA.img.flash
9.) rename pap2v2_fw_3.1.24_NA.img.web to pap2v2_fw_3.1.24_NA.img
10.) go to this link : http://192.168.X.XXX/cgi-bin/firmwarecfg you will be prompted for a user/pass : Admin / Admin or Admin /
11.) once your in that page go to : http://192.168.X.XXX/upgrade select your pap2v2_fw_3.1.24_NA.img wait for it to flash once done the pap2 will reboot
12.) you need to set your router to 192.168.1.1 because the pap2 v2 is now set as http://192.168.1.254 after that you can set your pap2 up with your new firmware
13.) enter all your magicjack info and click save. on the info screen you will see FAILED. this is ok click ADVANCED and then factory reset only the device not the provision state after it reboots you should be good to go.

^^^ i hope this guide helps out the people that need help with the pap2 v2 because it was a pain in the A$$ compared to the pap2 v1 ^^^

** after you flash with this firmware no commands on the phone will work. the default ip is 192.168.1.254 keep that in mind. you will need a hub or router or switch to talk to the device no direct connection will work ***

p0tsm0ke · Post by **p0tsm0ke** » Sat Mar 28, 2009 12:41 pm

seti007 it does not matter what firmware is on the pap2 v2 as you can downgrade it to any firmware. and then flash to this patched firmware.
i would make sure your unit is unlocked before flashing to the patched firmware.

step 12 should be user/pass admin/admin not Admin/Admin or Admin

the only time the Admin/Admin password is needed is when going in to ADMIN pages. other pages are just admin/admin or user and so on.

i hope they helps alot of people out.

http://192.168.X.XXX/cgi-bin/firmwarecfg = Admin/Admin or Admin/ = this can only load signed firmware
http://192.168.X.XXX/upgrade = Hidden update page that can load any firmware. ( thanks linksys )

also after you flash the patched firmware you will need to go to
http://192.168.1.254/voice/ <--- to access the page or you will get some 403 error just thought i would add that

coolcal · Post by **coolcal** » Wed Apr 08, 2009 11:24 pm

Hi - I did all the linux part. I have firmware version 1.00.16 running
I am unable to get to the upgrade page and get an option to upload file at the firmwarecfg page iteself? Does anyone have an idea wht I m doing wrong here?

p0tsm0ke · Post by **p0tsm0ke** » Sat Apr 25, 2009 8:19 pm

try the other firmware update page instead

magicJack and magicJack Plus Support, Reviews, FAQs and Tricks

pap2 ver2 config help

pap2 ver2 config help

Got it!!!