pap2: Error Message - Can't connect to login server

outofthesnow · Post by **outofthesnow** » Thu Mar 25, 2010 1:05 am

Here's the FIX

THANKS DTM!

Unless you have installed MJMD5 in the router firmware, you have to run it on another computer within your network. The PAP2 proxy should be using that computer's IP address and not pointed directly at the talk4free proxy. MJMD5 is essentially placed in between the PAP2 and the proxy server.

If you have MJMD5 installed in your router firmware, ignore this message. If not, then that probably is why you are unable to connect.
Well that's a simple fix!!
As soon as I ran MJMD5 on my PC and pointed it to the PC it worked like a charm, now need to get the DIAL plan correct

NOTE: Need to have TWO copies of MJMD5 running, for this to work correctly.

A correct dial plan from:
http://www.phoneservicesupport.com/magi ... t5066.html
Code: Select all
([1235-9]11!|411S0|<:1311>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0| 1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!|011!)
or DTM's dial plan posted to this page down below.
FWIW - Here is my dial plan which uses Google 411 directory assistance and also calls the 911 center directly if 911 is dialed on the phone. This also defaults to your local area code if only a 7 digit number is dialed.
Code: Select all
(*xx|<911:1AAAbbbbbbb>S0|<411:18004664411>S0|[235678]11!|<:1AAA>[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|<:1>[2-9]xx[2-9]xxxxxxS0)
Replace AAA with your area code. (two occurrences above)
Replace bbbbbbb with your local 911 center direct dial number.

I will later be getting one of my wrtg54 routers to work under dd-wrt linux
http://www.dd-wrt.com/

This will allow me to run the the PAP2 without a PC!
Which is my goal.

First thank you to all who have have created the tools and the know how!

My PAP box gives me this error message
-- Can't connect to login server

Read this and tried the hints especially this one :5070
proxy01.miami.talk4free.com:5070
http://www.phoneservicesupport.com/magi ... t5066.html

router is set up to pass through 5070 in both UDP and TCP
Service Name *5070
Protocol TCP
Global Port Range 5070 - 5070
Base Host Port 5070

&

Service Name *sip
Protocol UDP
Global Port Range 5070 - 5070
Base Host Port 5070

Even tried a completed IP Passthrough to no avail.

Was able to get MJMD5.exe & X-Lite to work both directions.

Used this to install a version of the firm ware.
http://www.unlockmypap2.com/

config from here:
http://rapidshare.com/files/208210096/PAP2TMJ.config

used spafcon to upload the .config file
http://www.opensky.ca/~jdhildeb/softwar ... downloads/

other sources of stuff
http://www.digitaloffensive.com/2010/03 ... /#more-121

and
more tools here: [many of the tools are here]
http://www.digitaloffensive.com/mj/mj.rar

first the PAP2 info screen:
Then the .config file

Code: Select all

DHCP:	Enabled	Current IP:	192.168.1.12
		Host Name:	LinksysPAP	Domain:	
		Current Netmask:	255.255.255.0	Current Gateway:	192.168.1.254
		Primary DNS:	192.168.1.254		
		Secondary DNS:	
Product Information	 	 				
		Product Name:	PAP2-NA	Serial Number:	FH912EC1xxxx
		Software Version:	3.1.22(LS)	Hardware Version:	0.03.4
		MAC Address:	0xxxF	Client Certificate:	Installed
		Customization:	Open		
System Status	 	 				
		Current Time:	3/25/2010 00:38:56	Elapsed Time:	00:02:01
		Broadcast Pkts Sent:	0	Broadcast Bytes Sent:	0
		Broadcast Pkts Recv:	254	Broadcast Bytes Recv:	15423
		Broadcast Pkts Dropped:	0	Broadcast Bytes Dropped:	0
		RTP Packets Sent:	0	RTP Bytes Sent:	0
		RTP Packets Recv:	0	RTP Bytes Recv:	0
		SIP Messages Sent:	10	SIP Bytes Sent:	5119
		SIP Messages Recv:	10	SIP Bytes Recv:	4061
		External IP:			
Line 1 Status	 	 				
		Display Name:	E_Phone_number01	User ID:	E_Phone_number01
		Hook State:	On	Registration State:	Can't connect to login server
		Last Registration At:	0/0/0 00:00:00	Next Registration In:	1080 s
		Message Waiting:	No	Call Back Active:	No
		Last Called Number:		Last Caller Number:	
		Mapped SIP Port:	5070		
		Call 1 State:	Idle	Call 2 State:	Idle
		Call 1 Tone:	None	Call 2 Tone:	None
		Call 1 Encoder:		Call 2 Encoder:	
		Call 1 Decoder:		Call 2 Decoder:	
		Call 1 FAX:		Call 2 FAX:	
		Call 1 Type:		Call 2 Type:	
		Call 1 Remote Hold:		Call 2 Remote Hold:	
		Call 1 Callback:		Call 2 Callback:	
		Call 1 Peer Name:		Call 2 Peer Name:	
		Call 1 Peer Phone:		Call 2 Peer Phone:	
		Call 1 Duration:		Call 2 Duration:	
		Call 1 Packets Sent:		Call 2 Packets Sent:	
		Call 1 Packets Recv:		Call 2 Packets Recv:	
		Call 1 Bytes Sent:		Call 2 Bytes Sent:	
		Call 1 Bytes Recv:		Call 2 Bytes Recv:	
		Call 1 Decode Latency:		Call 2 Decode Latency:	
		Call 1 Jitter:		Call 2 Jitter:	
		Call 1 Round Trip Delay:		Call 2 Round Trip Delay:	
		Call 1 Packets Lost:		Call 2 Packets Lost:	
		Call 1 Packet Error:		Call 2 Packet Error:	
		Call 1 Mapped RTP Port:		Call 2 Mapped RTP Port:	
Line 2 Status	 	 	


................................






! ATA config from 192.168.1.12 at Wed Mar 24 07:46:09 2010


#
# sip
#       

sip_max_forward = '70'

sip_max_redirection = '5'

sip_max_auth = '2'

sip_sip_user_agent_name = 'MagicJack/1.92.530e (SJ Labs)'

sip_sip_server_name = '$VERSION'

sip_sip_reg_user_agent_name = 'MagicJack/1.92.530e (SJ Labs)'

sip_sip_accept_language = ''

sip_dtmf_relay_mime_type = 'application/dtmf-relay'

sip_hook_flash_mime_type = 'application/hook-flash'

# possible values: 'yes', 'no'
sip_remove_last_reg = 'no'

# possible values: 'yes', 'no'
sip_use_compact_header = 'no'

# possible values: 'yes', 'no'
sip_escape_display_name = 'no'

# possible values: 'yes', 'no'
sip_rfc_2543_call_hold = 'yes'

# possible values: 'yes', 'no'
sip_mark_all_avt_packets = 'yes'

sip_sip_t1 = '.5'

sip_sip_t2 = '4'

sip_sip_t4 = '5'

sip_sip_timer_b = '32'

sip_sip_timer_f = '32'

sip_sip_timer_h = '32'

sip_sip_timer_d = '32'

sip_sip_timer_j = '32'

sip_invite_expires = '240'

sip_reinvite_expires = '30'

sip_reg_min_expires = '1'

sip_reg_max_expires = '7200'

sip_reg_retry_intvl = '30'

sip_reg_retry_long_intvl = '1200'

sip_reg_retry_random_delay = ''

sip_reg_retry_long_random_delay = ''

sip_reg_retry_intvl_cap = ''

sip_sit1_rsc = ''

sip_sit2_rsc = ''

sip_sit3_rsc = ''

sip_sit4_rsc = ''

sip_try_backup_rsc = ''

sip_retry_reg_rsc = ''

sip_rtp_port_min = '16384'

sip_rtp_port_max = '16482'

sip_rtp_packet_size = '0.030'

sip_max_rtp_icmp_err = '0'

sip_rtcp_tx_interval = '0'

# possible values: 'yes', 'no'
sip_no_udp_checksum = 'no'

# possible values: 'yes', 'no'
sip_stats_in_bye = 'no'

sip_nse_dynamic_payload = '100'

sip_avt_dynamic_payload = '101'

sip_inforeq_dynamic_payload = ''

sip_g726r16_dynamic_payload = '98'

sip_g726r24_dynamic_payload = '97'

sip_g726r32_dynamic_payload = '2'

sip_g726r40_dynamic_payload = '96'

sip_g729b_dynamic_payload = '99'

sip_nse_codec_name = 'NSE'

sip_avt_codec_name = 'telephone-event'

sip_g711u_codec_name = 'PCMU'

sip_g711a_codec_name = 'PCMA'

sip_g726r16_codec_name = 'G726-16'

sip_g726r24_codec_name = 'G726-24'

sip_g726r32_codec_name = 'G726-32'

sip_g726r40_codec_name = 'G726-40'

sip_g729a_codec_name = 'G729a'

sip_g729b_codec_name = 'G729ab'

sip_g723_codec_name = 'G723'

# possible values: 'yes', 'no'
sip_handle_via_received = 'no'

# possible values: 'yes', 'no'
sip_handle_via_rport = 'yes'

# possible values: 'yes', 'no'
sip_insert_via_received = 'no'

# possible values: 'yes', 'no'
sip_insert_via_rport = 'yes'

# possible values: 'yes', 'no'
sip_substitute_via_addr = 'yes'

# possible values: 'yes', 'no'
sip_send_resp_to_src_port = 'yes'

# possible values: 'yes', 'no'
sip_stun_enable = 'yes'

# possible values: 'yes', 'no'
sip_stun_test_enable = 'no'

sip_stun_server = 'stun.ekiga.net:3478'

sip_ext_ip = ''

sip_ext_rtp_port_min = ''

sip_nat_keep_alive_intvl = '15'


#
# regional
#       

regional_dial_tone = '350@-19,440@-19;10(*/0/1+2)'

regional_second_dial_tone = '420@-19,520@-19;10(*/0/1+2)'

regional_outside_dial_tone = '420@-16;10(*/0/1)'

regional_prompt_tone = '520@-19,620@-19;10(*/0/1+2)'

regional_busy_tone = '480@-19,620@-19;10(.5/.5/1+2)'

regional_reorder_tone = '480@-19,620@-19;10(.25/.25/1+2)'

regional_off_hook_warning_tone = '480@-10,620@0;10(.125/.125/1+2)'

regional_ring_back_tone = '440@-19,480@-19;*(2/4/1+2)'

regional_confirm_tone = '600@-16;1(.25/.25/1)'

regional_sit1_tone = '985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)'

regional_sit2_tone = '914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)'

regional_sit3_tone = '914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)'

regional_sit4_tone = '985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)'

regional_mwi_dial_tone = '350@-19,440@-19;2(.1/.1/1+2);10(*/0/1+2)'

regional_cfwd_dial_tone = '350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)'

regional_dnd_dial_tone = '350@-19,440@-19;2(.2/.2/2);10(*/0/1+2)'

regional_holding_tone = '600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)'

regional_conference_tone = '350@-19;20(.1/.1/1,.1/9.7/1)'

regional_secure_call_indication_tone = '397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)'

regional_feature_invocation_tone = '350@-16;*(.1/.1/1)'

regional_ring1_cadence = '60(2/4)'

regional_ring2_cadence = '60(.8/.4,.8/4)'

regional_ring3_cadence = '60(.4/.2,.4/.2,.8/4)'

regional_ring4_cadence = '60(.3/.2,1/.2,.3/4)'

regional_ring5_cadence = '1(.5/.5)'

regional_ring6_cadence = '60(.2/.4,.2/.4,.2/4)'

regional_ring7_cadence = '60(.4/.2,.4/.2,.4/4)'

regional_ring8_cadence = '60(0.25/9.75)'

regional_cwt1_cadence = '30(.3/9.7)'

regional_cwt2_cadence = '30(.1/.1, .1/9.7)'

regional_cwt3_cadence = '30(.1/.1, .1/.1, .1/9.7)'

regional_cwt4_cadence = '30(.1/.1,.3/.1,.1/9.3)'

regional_cwt5_cadence = '1(.5/.5)'

regional_cwt6_cadence = '30(.1/.1,.3/.2,.3/9.1)'

regional_cwt7_cadence = '30(.3/.1,.3/.1,.1/9.1)'

regional_cwt8_cadence = '2.3(.3/2)'

regional_ring1_name = 'Bellcore-r1'

regional_ring2_name = 'Bellcore-r2'

regional_ring3_name = 'Bellcore-r3'

regional_ring4_name = 'Bellcore-r4'

regional_ring5_name = 'Bellcore-r5'

regional_ring6_name = 'Bellcore-r6'

regional_ring7_name = 'Bellcore-r7'

regional_ring8_name = 'Bellcore-r8'

# possible values: 'Sinusoid', 'Trapezoid'
regional_ring_waveform = 'Trapezoid'

regional_ring_frequency = '20'

regional_ring_voltage = '85'

regional_cwt_frequency = '440@-10'

# possible values: 'yes', 'no'
regional_synchronized_ring = 'no'

regional_hook_flash_timer_min = '.1'

regional_hook_flash_timer_max = '.9'

regional_callee_on_hook_delay = '0'

regional_reorder_delay = '5'

regional_call_back_expires = '1800'

regional_call_back_retry_intvl = '30'

regional_call_back_delay = '.5'

regional_vmwi_refresh_intvl = '0'

regional_interdigit_long_timer = '10'

regional_interdigit_short_timer = '3'

regional_cpc_delay = '2'

regional_cpc_duration = '0'

regional_call_return_code = '*69'

regional_blind_transfer_code = '*98'

regional_call_back_act_code = '*66'

regional_call_back_deact_code = '*86'

regional_cfwd_all_act_code = '*72'

regional_cfwd_all_deact_code = '*73'

regional_cfwd_busy_act_code = '*90'

regional_cfwd_busy_deact_code = '*91'

regional_cfwd_no_ans_act_code = '*92'

regional_cfwd_no_ans_deact_code = '*93'

regional_cfwd_last_act_code = '*63'

regional_cfwd_last_deact_code = '*83'

regional_block_last_act_code = '*60'

regional_block_last_deact_code = '*80'

regional_accept_last_act_code = '*64'

regional_accept_last_deact_code = '*84'

regional_cw_act_code = '*56'

regional_cw_deact_code = '*57'

regional_cw_per_call_act_code = '*71'

regional_cw_per_call_deact_code = '*70'

regional_block_cid_act_code = '*67'

regional_block_cid_deact_code = '*68'

regional_block_cid_per_call_act_code = '*81'

regional_block_cid_per_call_deact_code = '*82'

regional_block_anc_act_code = '*77'

regional_block_anc_deact_code = '*87'

regional_dnd_act_code = '*78'

regional_dnd_deact_code = '*79'

regional_cid_act_code = '*65'

regional_cid_deact_code = '*85'

regional_cwcid_act_code = '*25'

regional_cwcid_deact_code = '*45'

regional_dist_ring_act_code = '*26'

regional_dist_ring_deact_code = '*46'

regional_speed_dial_act_code = '*74'

regional_secure_all_call_act_code = '*16'

regional_secure_no_call_act_code = '*17'

regional_secure_one_call_act_code = '*18'

regional_secure_one_call_deact_code = '*19'

regional_conference_act_code = ''

regional_attn_xfer_act_code = ''

regional_modem_line_toggle_code = '*99'

regional_referral_services_codes = ''

regional_feature_dial_services_codes = ''

regional_service_annc_base_number = ''

regional_service_annc_extension_codes = ''

regional_prefer_g711u_code = '*017110'

regional_force_g711u_code = '*027110'

regional_prefer_g711a_code = '*017111'

regional_force_g711a_code = '*027111'

regional_prefer_g723_code = '*01723'

regional_force_g723_code = '*02723'

regional_prefer_g726r16_code = '*0172616'

regional_force_g726r16_code = '*0272616'

regional_prefer_g726r24_code = '*0172624'

regional_force_g726r24_code = '*0272624'

regional_prefer_g726r32_code = '*0172632'

regional_force_g726r32_code = '*0272632'

regional_prefer_g726r40_code = '*0172640'

regional_force_g726r40_code = '*0272640'

regional_prefer_g729a_code = '*01729'

regional_force_g729a_code = '*02729'

regional_set_local_date__mm_dd_ = ''

regional_set_local_time__hh_mm_ = ''

# possible values: 'GMT-12:00', 'GMT-11:00', 'GMT-10:00', 'GMT-09:00', 'GMT-08:00', 'GMT-07:00', 'GMT-06:00', 'GMT-05:00', 'GMT-04:00', 'GMT-03:30', 'GMT-03:00', 'GMT-02:00', 'GMT-01:00', 'GMT', 'GMT+01:00', 'GMT+02:00', 'GMT+03:00', 'GMT+03:30', 'GMT+04:00', 'GMT+05:00', 'GMT+05:30', 'GMT+05:45', 'GMT+06:00', 'GMT+06:30', 'GMT+07:00', 'GMT+08:00', 'GMT+09:00', 'GMT+09:30', 'GMT+10:00', 'GMT+11:00', 'GMT+12:00', 'GMT+13:00'
regional_time_zone = 'GMT-05:00'

# possible values: '600', '900', '600+2.16uF', '900+2.16uF', '270+750||150nF', '220+820||120nF', '220+820||115nF', '370+620||310nF'
regional_fxs_port_impedance = '600'

regional_daylight_saving_time_rule = 'start=3/8/7/2:00;end=11/1/7/2:00;save=1'

regional_fxs_port_input_gain = '-3'

regional_fxs_port_output_gain = '-3'

regional_dtmf_playback_level = '-16'

regional_dtmf_playback_length = '.1'

# possible values: 'yes', 'no'
regional_detect_abcd = 'yes'

# possible values: 'yes', 'no'
regional_playback_abcd = 'yes'

# possible values: 'Bellcore(N.Amer,China)', 'DTMF(Finland,Sweden)', 'DTMF(Denmark)', 'ETSI DTMF', 'ETSI DTMF With PR', 'ETSI DTMF After Ring', 'ETSI FSK', 'ETSI FSK With PR(UK)', 'DTMF(Denmark) With PR'
regional_caller_id_method = 'Bellcore(N.Amer,China)'

# possible values: '1', '2', '3', '4', '5', '6', '7', '8'
regional_fxs_port_power_limit = '3'

# possible values: 'bell 202', 'v.23'
regional_caller_id_fsk_standard = 'bell 202'

# possible values: 'Default', 'Sweden'
regional_feature_invocation_method = 'Default'

# possible values: 'yes', 'no'
regional_more_echo_suppression = 'no'


#
# system
#       

system_restricted_access_domains = ''

# possible values: 'yes', 'no'
system_enable_web_server = 'yes'

system_web_server_port = '80'

# possible values: 'yes', 'no'
system_enable_web_admin_access = 'yes'

system_admin_passwd = '*************'

system_user_password = ''

# possible values: 'yes', 'no'
system_dhcp = 'yes'

system_static_ip = ''

system_netmask = ''

system_gateway = ''

system_hostname = ''

system_domain = ''

system_primary_dns = ''

system_secondary_dns = ''

# possible values: 'Manual', 'Manual,DHCP', 'DHCP,Manual'
system_dns_server_order = 'DHCP,Manual'

# possible values: 'Parallel', 'Sequential'
system_dns_query_mode = 'Parallel'

system_syslog_server = ''

system_debug_server = ''

# possible values: '0', '1', '2', '3', '0+H', '1+H', '2+H', '3+H', '99'
system_debug_level = '0'

system_primary_ntp_server = '0.us.pool.ntp.org'

system_secondary_ntp_server = 'time.mit.edu'


#
# provisioning
#       

# possible values: 'yes', 'no'
provisioning_provision_enable = 'yes'

# possible values: 'yes', 'no'
provisioning_resync_on_reset = 'yes'

provisioning_resync_random_delay = '2'

provisioning_resync_periodic = '3600'

provisioning_resync_error_retry_delay = '3600'

provisioning_forced_resync_delay = '14400'

# possible values: 'yes', 'no'
provisioning_resync_from_sip = 'yes'

# possible values: 'yes', 'no'
provisioning_resync_after_upgrade_attempt = 'yes'

provisioning_resync_trigger_1 = ''

provisioning_resync_trigger_2 = ''

# possible values: 'yes', 'no'
provisioning_resync_fails_on_fnf = 'no'

provisioning_profile_rule = '/init.cfg'

provisioning_profile_rule_b = ''

provisioning_profile_rule_c = ''

provisioning_profile_rule_d = ''

provisioning_log_resync_request_msg = '$PN $MAC -- Requesting resync $SCHEME://$SERVIP:$PORT$PATH'

provisioning_log_resync_success_msg = '$PN $MAC -- Successful resync $SCHEME://$SERVIP:$PORT$PATH'

provisioning_log_resync_failure_msg = '$PN $MAC -- Resync failed: $ERR'

provisioning_report_rule = ''

# possible values: 'yes', 'no'
provisioning_upgrade_enable = 'yes'

provisioning_upgrade_error_retry_delay = '3600'

provisioning_downgrade_rev_limit = ''

provisioning_upgrade_rule = ''

provisioning_log_upgrade_request_msg = '$PN $MAC -- Requesting upgrade $SCHEME://$SERVIP:$PORT$PATH'

provisioning_log_upgrade_success_msg = '$PN $MAC -- Successful upgrade $SCHEME://$SERVIP:$PORT$PATH -- $ERR'

provisioning_log_upgrade_failure_msg = '$PN $MAC -- Upgrade failed: $ERR'

provisioning_gpp_a = ''

provisioning_gpp_b = ''

provisioning_gpp_c = ''

provisioning_gpp_d = ''

provisioning_gpp_e = ''

provisioning_gpp_f = ''

provisioning_gpp_g = ''

provisioning_gpp_h = ''

provisioning_gpp_i = ''

provisioning_gpp_j = ''

provisioning_gpp_k = ''

provisioning_gpp_l = ''

provisioning_gpp_m = ''

provisioning_gpp_n = ''

provisioning_gpp_o = ''

provisioning_gpp_p = ''

#
# user_1
#       

user_1_cfwd_all_dest = ''

user_1_cfwd_busy_dest = ''

user_1_cfwd_no_ans_dest = ''

user_1_cfwd_no_ans_delay = '20'

user_1_cfwd_sel1_caller = ''

user_1_cfwd_sel1_dest = ''

user_1_cfwd_sel2_caller = ''

user_1_cfwd_sel2_dest = ''

user_1_cfwd_sel3_caller = ''

user_1_cfwd_sel3_dest = ''

user_1_cfwd_sel4_caller = ''

user_1_cfwd_sel4_dest = ''

user_1_cfwd_sel5_caller = ''

user_1_cfwd_sel5_dest = ''

user_1_cfwd_sel6_caller = ''

user_1_cfwd_sel6_dest = ''

user_1_cfwd_sel7_caller = ''

user_1_cfwd_sel7_dest = ''

user_1_cfwd_sel8_caller = ''

user_1_cfwd_sel8_dest = ''

user_1_cfwd_last_caller = ''

user_1_cfwd_last_dest = ''

user_1_block_last_caller = ''

user_1_accept_last_caller = ''

user_1_speed_dial_2 = ''

user_1_speed_dial_3 = ''

user_1_speed_dial_4 = ''

user_1_speed_dial_5 = ''

user_1_speed_dial_6 = ''

user_1_speed_dial_7 = ''

user_1_speed_dial_8 = ''

user_1_speed_dial_9 = ''

# possible values: 'yes', 'no'
user_1_cw_setting = 'yes'

# possible values: 'yes', 'no'
user_1_block_cid_setting = 'no'

# possible values: 'yes', 'no'
user_1_block_anc_setting = 'no'

# possible values: 'yes', 'no'
user_1_dnd_setting = 'no'

# possible values: 'yes', 'no'
user_1_cid_setting = 'yes'

# possible values: 'yes', 'no'
user_1_cwcid_setting = 'yes'

# possible values: 'yes', 'no'
user_1_dist_ring_setting = 'no'

# possible values: 'yes', 'no'
user_1_secure_call_setting = 'no'

# possible values: 'yes', 'no'
user_1_message_waiting = 'no'

# possible values: 'yes', 'no'
user_1_dnd_activated = 'no'

user_1_ring1_caller = ''

user_1_ring2_caller = ''

user_1_ring3_caller = ''

user_1_ring4_caller = ''

user_1_ring5_caller = ''

user_1_ring6_caller = ''

user_1_ring7_caller = ''

user_1_ring8_caller = ''

# possible values: '1', '2', '3', '4', '5', '6', '7', '8'
user_1_default_ring = '1'

# possible values: '1', '2', '3', '4', '5', '6', '7', '8'
user_1_default_cwt = '1'

# possible values: '1', '2', '3', '4', '5', '6', '7', '8', 'none'
user_1_hold_reminder_ring = '8'

# possible values: '1', '2', '3', '4', '5', '6', '7', '8'
user_1_call_back_ring = '7'

user_1_cfwd_ring_splash_len = '0'

user_1_cblk_ring_splash_len = '0'

user_1_vmwi_ring_splash_len = '0'

# possible values: 'New VM Available', 'New VM Becomes Available', 'New VM Arrives'
user_1_vmwi_ring_policy = 'New VM Available'

# possible values: 'yes', 'no'
user_1_ring_on_no_new_vm = 'no'


#
# line_1
#       

# possible values: 'yes', 'no'
line_1_line_enable = 'yes'

# possible values: 'yes', 'no'
line_1_sas_enable = 'no'

line_1_sas_dlg_refresh_intvl = '30'

line_1_sas_inbound_rtp_sink = ''

# possible values: 'yes', 'no'
line_1_nat_mapping_enable = 'yes'

# possible values: 'yes', 'no'
line_1_nat_keep_alive_enable = 'yes'

line_1_nat_keep_alive_msg = '$NOTIFY'

line_1_nat_keep_alive_dest = '$PROXY'

line_1_sip_tos_diffserv_value = '0x68'

# possible values: 'low', 'medium', 'high', 'very high', 'extremely high'
line_1_network_jitter_level = 'very high'

line_1_rtp_tos_diffserv_value = '0xb8'

# possible values: 'up and down', 'up only', 'down only', 'disable'
line_1_jitter_buffer_adjustment = 'up and down'

line_1_sip_port = '5070'

# possible values: 'yes', 'no'
line_1_sip_100rel_enable = 'no'

line_1_ext_sip_port = '5070'

# possible values: 'yes', 'no'
line_1_auth_resync_reboot = 'yes'

# possible values: 'yes', 'no'
line_1_auth_invite = 'no'

# possible values: 'yes', 'no'
line_1_auth_mwi = 'no'

line_1_sip_proxy_require = ''

# possible values: 'yes', 'no'
line_1_sip_remote_party_id = 'no'

# possible values: 'yes', 'no'
line_1_sip_guid = 'no'

# possible values: 'none', '1-line', '1-line excl. OPT', '1-line excl. NTFY', '1-line excl. REG', '1-line excl. OPT|NTFY|REG', 'full', 'full excl. OPT', 'full excl. NTFY', 'full excl. REG', 'full excl. OPT|NTFY|REG'
line_1_sip_debug_option = 'none'

line_1_rtp_log_intvl = '0'

# possible values: 'yes', 'no'
line_1_restrict_source_ip = 'no'

line_1_referor_bye_delay = '4'

line_1_refer_target_bye_delay = '0'

line_1_referee_bye_delay = '0'

# possible values: 'yes', 'no'
line_1_refer_to_target_contact = 'no'

# possible values: 'yes', 'no'
line_1_sticky_183 = 'no'

# possible values: 'yes', 'no'
line_1_blind_attn_xfer_enable = 'no'

line_1_moh_server = ''

# possible values: 'yes', 'no'
line_1_xfer_when_hangup_conf = 'yes'

line_1_conference_bridge_url = ''

# possible values: '3', '4', '5', '6', '7', '8', '9', '10'
line_1_conference_bridge_ports = '3'

line_1_proxy = proxy01.miami.talk4free.com:5070 '

# possible values: 'yes', 'no'
line_1_use_outbound_proxy = 'no'

line_1_outbound_proxy = ''

# possible values: 'yes', 'no'
line_1_use_ob_proxy_in_dialog = 'yes'

# possible values: 'yes', 'no'
line_1_register = 'yes'

# possible values: 'yes', 'no'
line_1_make_call_without_reg = 'no'

line_1_register_expires = '180'

# possible values: 'yes', 'no'
line_1_ans_call_without_reg = 'no'

# possible values: 'yes', 'no'
line_1_use_dns_srv = 'no'

# possible values: 'yes', 'no'
line_1_dns_srv_auto_prefix = 'no'

line_1_proxy_fallback_intvl = '3600'

# possible values: 'Normal', 'Based on SRV Port'
line_1_proxy_redundancy_method = 'Normal'

line_1_voice_mail_server = ''

line_1_mailbox_subscribe_expires = '2147483647'

line_1_display_name = 'Exxxxxxxxxx01'

line_1_user_id = 'Exxxxxxxxxx01'

line_1_password = '*************'

# possible values: 'yes', 'no'
line_1_use_auth_id = 'no'

line_1_auth_id = 'Exxxxxxxxxx01' 

line_1_mini_certificate = ''

line_1_srtp_private_key = ''

# possible values: 'yes', 'no'
line_1_call_waiting_serv = 'yes'

# possible values: 'yes', 'no'
line_1_block_cid_serv = 'yes'

# possible values: 'yes', 'no'
line_1_block_anc_serv = 'yes'

# possible values: 'yes', 'no'
line_1_dist_ring_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cfwd_all_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cfwd_busy_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cfwd_no_ans_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cfwd_sel_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cfwd_last_serv = 'yes'

# possible values: 'yes', 'no'
line_1_block_last_serv = 'yes'

# possible values: 'yes', 'no'
line_1_accept_last_serv = 'yes'

# possible values: 'yes', 'no'
line_1_dnd_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cid_serv = 'yes'

# possible values: 'yes', 'no'
line_1_cwcid_serv = 'yes'

# possible values: 'yes', 'no'
line_1_call_return_serv = 'yes'

# possible values: 'yes', 'no'
line_1_call_back_serv = 'yes'

# possible values: 'yes', 'no'
line_1_three_way_call_serv = 'yes'

# possible values: 'yes', 'no'
line_1_three_way_conf_serv = 'yes'

# possible values: 'yes', 'no'
line_1_attn_transfer_serv = 'yes'

# possible values: 'yes', 'no'
line_1_unattn_transfer_serv = 'yes'

# possible values: 'yes', 'no'
line_1_mwi_serv = 'yes'

# possible values: 'yes', 'no'
line_1_vmwi_serv = 'no'

# possible values: 'yes', 'no'
line_1_speed_dial_serv = 'yes'

# possible values: 'yes', 'no'
line_1_secure_call_serv = 'yes'

# possible values: 'yes', 'no'
line_1_referral_serv = 'yes'

# possible values: 'yes', 'no'
line_1_feature_dial_serv = 'yes'

# possible values: 'yes', 'no'
line_1_service_announcement_serv = 'no'

# possible values: 'G711u', 'G711a', 'G726-16', 'G726-24', 'G726-32', 'G726-40', 'G729a', 'G723'
line_1_preferred_codec = 'G711u'

# possible values: 'yes', 'no'
line_1_silence_supp_enable = 'no'

# possible values: 'yes', 'no'
line_1_use_pref_codec_only = 'yes'

# possible values: 'high', 'medium', 'low'
line_1_silence_threshold = 'medium'

# possible values: 'yes', 'no'
line_1_g729a_enable = 'yes'

# possible values: 'yes', 'no'
line_1_echo_canc_enable = 'yes'

# possible values: 'yes', 'no'
line_1_g723_enable = 'yes'

# possible values: 'yes', 'no'
line_1_echo_canc_adapt_enable = 'yes'

# possible values: 'yes', 'no'
line_1_g726_16_enable = 'yes'

# possible values: 'yes', 'no'
line_1_echo_supp_enable = 'yes'

# possible values: 'yes', 'no'
line_1_g726_24_enable = 'yes'

# possible values: 'yes', 'no'
line_1_fax_ced_detect_enable = 'yes'

# possible values: 'yes', 'no'
line_1_g726_32_enable = 'yes'

# possible values: 'yes', 'no'
line_1_fax_cng_detect_enable = 'yes'

# possible values: 'yes', 'no'
line_1_g726_40_enable = 'yes'

# possible values: 'G711u', 'G711a'
line_1_fax_passthru_codec = 'G711u'

# possible values: 'yes', 'no'
line_1_dtmf_process_info = 'yes'

# possible values: 'yes', 'no'
line_1_fax_codec_symmetric = 'yes'

# possible values: 'yes', 'no'
line_1_dtmf_process_avt = 'yes'

# possible values: 'None', 'NSE', 'ReINVITE'
line_1_fax_passthru_method = 'NSE'

# possible values: 'InBand', 'AVT', 'INFO', 'Auto'
line_1_dtmf_tx_method = 'Auto'

# possible values: 'Normal', 'Strict'
line_1_dtmf_tx_mode = 'Strict'

# possible values: 'yes', 'no'
line_1_fax_process_nse = 'yes'

# possible values: 'None', 'AVT', 'INFO'
line_1_hook_flash_tx_method = 'None'

# possible values: 'yes', 'no'
line_1_fax_disable_ecan = 'no'

# possible values: 'yes', 'no'
line_1_release_unused_codec = 'yes'

line_1_dial_plan = '([1235-9]11!|411S0|<:1311>[2-9]xxxxxxS0|1[2-9]xx[2-9]xxxxxxS0| 1441!|1473!|1649!|1758!|1767!|1784!|1876!|1[26][68]4!|1[28]68!| 124[26]!|134[05]!|167[01]!|18[06]9!|011!)'

# possible values: 'yes', 'no'
line_1_enable_ip_dialing = 'no'

line_1_emergency_number = ''

# possible values: 'Forward', 'Reverse'
line_1_idle_polarity = 'Forward'

# possible values: 'Forward', 'Reverse'
line_1_caller_conn_polarity = 'Forward'

# possible values: 'Forward', 'Reverse'
line_1_callee_conn_polarity = 'Forward'

madhatterm · Post by **madhatterm** » Thu Mar 25, 2010 8:27 pm

setup my magic jack last june on the PAP2. Its been working great since today at around 1:00. now I am getting Can't connect to login server also
I thinking Magic jack updated something.

antman1 · Post by **antman1** » Fri Mar 26, 2010 6:36 am

I had the same problem. This was a week ago. What I did first was update my agent string and then I tried it again. It still did not log in so then I thought my RTP300 days were over so I hooked up my Magicjack dongle (without my rtp300 plugged in) then it said "Upgrading Lucky You" and then when it was done and working I unplugged the dongle and hooked my RTP300 back up and it was working again. weird stuff but it seems like they knew my Dongle never updated and it wouldn't register with the server until it did.

dtm · Post by **dtm** » Fri Mar 26, 2010 10:58 am

line_1_proxy = proxy01.miami.talk4free.com:5070

Shouldn't this instead be pointed at the computer running MJMD5?

madhatterm · Post by **madhatterm** » Fri Mar 26, 2010 1:34 pm

some of us that are running the routers and Pap2 devices don't have magic jack running on the computer there is a setting when you dump the memory that is the proxy to point to.

dtm · Post by **dtm** » Fri Mar 26, 2010 6:22 pm

Unless you have installed MJMD5 in the router firmware, you have to run it on another computer within your network. The PAP2 proxy should be using that computer's IP address and not pointed directly at the talk4free proxy. MJMD5 is essentially placed in between the PAP2 and the proxy server.

If you have MJMD5 installed in your router firmware, ignore this message. If not, then that probably is why you are unable to connect.

outofthesnow · Post by **outofthesnow** » Sat Mar 27, 2010 12:10 am

THANKS DTM!

Unless you have installed MJMD5 in the router firmware, you have to run it on another computer within your network. The PAP2 proxy should be using that computer's IP address and not pointed directly at the talk4free proxy. MJMD5 is essentially placed in between the PAP2 and the proxy server.

If you have MJMD5 installed in your router firmware, ignore this message. If not, then that probably is why you are unable to connect.

Well that's a simple fix!!
As soon as I ran MJMD5 on my PC and pointed it to the PC it worked like a charm, now need to get the DIAL plan correct

madhatterm · Post by **madhatterm** » Sat Mar 27, 2010 12:07 pm

Can you guys explain your setup. When I setup my PAP2 a year ago I used all the same settings you use and the info I got from dumping the sip credentials. I never ran the MJMD5 on another computer. it just work with there proxy in the PAP2. It just stop working this week. I have try to setup the MJMD5 on my computer and point it to the computer for the proxy in the PAP2 but I still get no dial tone. Can you guys give me some assistance as to what I am doing wrong.
Thanks

dtm · Post by **dtm** » Sat Mar 27, 2010 3:27 pm

"Can you guys explain your setup."

Download MJMD5 and run it on a computer that is on the same network as your PAP2. MJMD5 should be pointed at the talk4free proxy you use such as proxy01.miami.talk4free.com. I prefer to use the actaul IP address of the proxy instead of the name. MJMD5 also needs your 20 character password.

The proxy setting in the PAP2 should be pointed at the IP address of the network computer running MJMD5. Something like: 192.168.1.193:5070

Everything else is normal.

dtm · Post by **dtm** » Sat Mar 27, 2010 3:40 pm

FWIW - Here is my dial plan which uses Google 411 directory assistance and also calls the 911 center directly if 911 is dialed on the phone. This also defaults to your local area code if only a 7 digit number is dialed.

(*xx|<911:1AAAbbbbbbb>S0|<411:18004664411>S0|[235678]11!|<:1AAA>[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|<:1>[2-9]xx[2-9]xxxxxxS0)

Replace AAA with your area code. (two occurrences above)
Replace bbbbbbb with your local 911 center direct dial number.

outofthesnow · Post by **outofthesnow** » Sat Mar 27, 2010 8:04 pm

Again thanks DTM for the dial plan!

sabresfan · Post by **sabresfan** » Sat Mar 27, 2010 8:22 pm

dtm wrote:FWIW - Here is my dial plan which uses Google 411 directory assistance and also calls the 911 center directly if 911 is dialed on the phone. This also defaults to your local area code if only a 7 digit number is dialed.

(*xx|<911:1AAAbbbbbbb>S0|<411:18004664411>S0|[235678]11!|<:1AAA>[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|<:1>[2-9]xx[2-9]xxxxxxS0)

Replace AAA with your area code. (two occurrences above)
Replace bbbbbbb with your local 911 center direct dial number.

This is a great dial plan. Just to let some people know finding the direct number to call your local 911 call center may not be easy to get. Just yesterday I spent a few hours calling local government offices and looking online and the number is unlisted in my county. When I asked the local government officials for the number they became agitated and said it's just 911. Finally I had a friend with a really old phonebook (1993) that lives out in the sticks look it up and it was listed. They must be hurting for cash and want to collect all the $ they can get their hands on (911 fees). But on a serious note to people make sure you test your 911 if you set it up yourself and make sure you remember your address.

magicJack and magicJack Plus Support, Reviews, FAQs and Tricks