New Toy: GVOut Google Voice Outgoing Proxy Dialer (Windows)

synchron · Post by **synchron** » Tue Sep 01, 2009 11:51 am

doohickey wrote:
So, for completely free calling, all calls must be initiated through Google Voice, hence the use of GVOut. Another reason to initiate all calls through Google Voice is quality, it's fantastic, and not just relatively speaking, it really has great quality. That's my experience, anyway.

I'm not convinced that GV has anything to do with the quality. I've tried the USA echo test with the GV web callback feature once going through Gizmo and once going through Sipgate - the Gizmo route was slightly garbled but Sipgate was crystal clear but about 1 second more of a delay. GV just initiates the call to the selected provider which handles then handles the RTP voice transmission/reception packets.

My 2 cents.

Synchron

degarb · Post by **degarb** » Tue Sep 01, 2009 12:25 pm

synchron wrote: This is not to say anything negative about the developer(s) since the mjmd5 proxy works rock solid with any brand ATA and any brand softphone including xlite.

My primary phone system is now SS/Sipgate/GV which has been solid going on the 4th day now. I would not knock Sipgate's tech support, they answer E-mails within 24 hours and their website is pretty informative. For a free incoming Voip service, they are much better compared to Gizmo/VoxOx IMO.

Synchron

I follow most of your post. What is SS? And I am guessing mjmd5 is some proxy for magic jack. Not familiar.

synchron · Post by **synchron** » Tue Sep 01, 2009 1:05 pm

SS= Sipsorcery, an experimental Voip switching system that allows for multiple providers. You specify your incoming and outgoing providers through a sophisticated Ruby dialer script. SS now allows any free incoming Voip provider with the GV callback feature similar to what the GVOut proxy is doing. The big difference is that they act as the "proxy" so you don't need your PC/laptop on.

Unfortunately, they are asking newbies to check back 9/8 to allow for new accounts so if you will have to wait at least until then to try them out.

Synchron

degarb · Post by **degarb** » Tue Sep 01, 2009 2:19 pm

SS work better than gv out then?

I don't see a sign up page for ss.

Notwithstanding Why I don't understand need for a download if they are running the proxy and holding my settings, I downloaded some sipsorcerer program but at first glance, looks like you need to dl silverlight engine. Not sure how you would run the program which looks very cryptic. Even the doc is a docx extension which I can't seem to get open office to open or word.

doohickey · Post by **doohickey** » Tue Sep 01, 2009 8:01 pm

synchron wrote:I'm not convinced that GV has anything to do with the quality.

Yes, that's what I'm inclined to think as well since Gizmo5 is my carrier regardless of how I initiate the call. But in practice, a call initiated though Gizmo5 is always poor quality, while one initiated through Google Voice is always excellent. Go figure.

synchron · Post by **synchron** » Tue Sep 01, 2009 11:07 pm

degarb wrote: I don't see a sign up page for ss.

http://www.sipsorcery.com

And, yes, Microsoft Silverlight, latest version is a prerequisite to signing up - which is now locked until at least a week from now.

Synchron

doublehelix · Post by **doublehelix** » Wed Sep 02, 2009 12:44 am

I am getting the following error. Before trying the ATA, tried to use X-lite. If I point to the proxy, it cannot register. X-lite by itself works fine.

Another issue also: Cannot receive calls from another phone to GV, but can call from GV and it rings on x-lite or gizmo without GV out proxy.

Please help? Am I missing any other install package?

Starting Proxy on port 5060
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Server Sent: SIP/2.0 401 Unauthorized
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Server Sent: SIP/2.0 200 OK
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Server Sent: SIP/2.0 200 OK
Server Sent: SIP/2.0 200 OK
Server Sent: SIP/2.0 200 OK
Server Sent: SIP/2.0 200 OK
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
Server Sent: SIP/2.0 200 OK
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Server Sent: SUBSCRIBE sip:[email protected]:63989;rinstance=b6043b61d9a
6e1cd SIP/2.0
Server Sent: SUBSCRIBE sip:[email protected]:63989;rinstance=a4b01d97a54
1558a SIP/2.0
Server Sent: SUBSCRIBE sip:[email protected]:63989;rinstance=09c57a2ea5a
22ba6 SIP/2.0
Client Sent: SIP/2.0 489 Event Package Not Supported
Client Sent: SIP/2.0 489 Event Package Not Supported
Client Sent: SIP/2.0 489 Event Package Not Supported
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Client Sent: SUBSCRIBE sip:[email protected] SIP/2.0
Server Sent: SIP/2.0 408 Request Timeout

doublehelix · Post by **doublehelix** » Wed Sep 02, 2009 12:44 am

I am getting the following error. Before trying the ATA, tried to use X-lite. If I point to the proxy, it cannot register. X-lite by itself works fine.

Another issue also: Cannot receive calls from another phone to GV, but can call from GV and it rings on x-lite or gizmo without GV out proxy.

Please help? Am I missing any other install package? Thanks.

Starting Proxy on port 5060
Client connection from 192.168.1.245
Client Sent: REGISTER sip:proxy01.sipphone.com SIP/2.0
...
Server Sent: SUBSCRIBE ...
Server Sent: SIP/2.0 408 Request Timeout

*** It started working fine. Tested with 2 calls. Awesome utility. If you save settings, it uses plain text even for password. But, it works great.

degarb · Post by **degarb** » Wed Sep 02, 2009 7:36 am

synchron wrote:
degarb wrote: I don't see a sign up page for ss.

http://www.sipsorcery.com

And, yes, Microsoft Silverlight, latest version is a prerequisite to signing up - which is now locked until at least a week from now.

Synchron

Wiki has silverlight as a browser plugin, but doesn't say what browser. What browser does silverlight need?

Is this just what is needed to see signup?

synchron · Post by **synchron** » Wed Sep 02, 2009 10:17 am

degarb wrote:
Wiki has silverlight as a browser plugin, but doesn't say what browser. What browser does silverlight need?

Is this just what is needed to see signup?

Not sure what doesn't work but I believe the major ones are supported like Firefox, Opera, and of course Microsoft's IE.

I assume you are running a PC, not Mac or Linux - I think Silverlight only works on PC platform.

Synchron

doublehelix · Post by **doublehelix** » Wed Sep 02, 2009 10:58 pm

synchron wrote:Well, with the latest GVout, I finally got things to work, (sort of) with G5 using the debug mode cmd window to help. What's weird is that I have to set the ATA up so that it doesn't register and no dialtone. This means that I leave the SIP domain empty (no proxy01.sipphone.com entry) and I just stick the PC IP address in SIP Proxy field.

So, with no dialtone, I can still dial out, disconnect, see the correct status in the cmd window and get the GV callback ring. With the ATA registered and a dialtone, I don't get the constant client messages from the ATA IP address and it won't work.

Weird, to dial out with no dialtone, but it works, nevertheless. This is with the Sunrocket/Vonics/Innomedia ATA. It works best if you set GVout to no delay/no busy tone.

Synchron

Innomedia ATA:
Been trying every setting +- SIP Domain, Register timeout 60-3600...
I tried with Registered/dialtone and without as you suggested. GVOut shows outgoing call and that is the last. No callback...

Only works with SIP softphone without problems. Help please?
Thanks,
vic

doublehelix · Post by **doublehelix** » Thu Sep 03, 2009 9:18 am

Josemiami wrote:For the people interested in trying a different soft phone this is a free software version of a free soft phone with 6 lines. ...

This is the link for the web page:

http://www.nch.com.au/talk/index.html

This works great and better then the x-lite 4 beta. I have been using x-lite for the longest time and the older program ver 3 has more options. Great find Jose.

mel2000 · Post by **mel2000** » Thu Sep 03, 2009 4:09 pm

NCH ExpressTalk freeware appears to support only one SIP account, unlike PhonerLite.

degarb · Post by **degarb** » Thu Sep 03, 2009 9:19 pm

mel2000 wrote:NCH ExpressTalk freeware appears to support only one SIP account, unlike PhonerLite.

url for phonelite.

I got googlevoiceout to work with nch expresstalk. It doesn't give me the 408 error or the sipstack crash error. The trick is use sipgate.com for server and under advanced use 192.168.0.10:5060 or what ever ip, for the outgoing server.

I used processlasso to disallow magicjack.exe and mjsetup.exe and I can use the magicjack dongle and phone. I would be super duper excited at this magicjack backup plan, except I cannot answer or dial without the softphone. client. You would think if I pick up, the mic input could answer and if no volume input level after 30 seconds it would auto hangup. also listen for keypad.

I ordered the pap2t from amazon. I will see it I can get google voice out working with it.

mel2000 · Post by **mel2000** » Thu Sep 03, 2009 10:47 pm

PhonerLite url
http://www.phonerlite.de/index_en.htm

degarb · Post by **degarb** » Sat Sep 05, 2009 10:15 pm

mel2000 wrote:PhonerLite url
http://www.phonerlite.de/index_en.htm

Got express talk to work with gvout. Phonelite, no. What is trick with it?

degarb · Post by **degarb** » Sat Sep 05, 2009 10:45 pm

synchron wrote:
degarb wrote: I don't see a sign up page for ss.

http://www.sipsorcery.com

And, yes, Microsoft Silverlight, latest version is a prerequisite to signing up - which is now locked until at least a week from now.

Synchron

I installed silverlight against better judgment and googling returns it is a backdoor to our computers. Still website is black on all browsers here.

degarb · Post by **degarb** » Sat Sep 05, 2009 10:54 pm

http://www.supershareware.com/get/free/soft-phone.html
A ton of free phones here.

Any one with any time to test until they find one that works with google voice out and can be controlled with phone without need of touching the computer?

doohickey · Post by **doohickey** » Sun Sep 06, 2009 12:24 pm

GVOut isn't working so well for me anymore. It will successfully initiate one call and that's it.

I use the dial plan method on port 5060. I've tried both with and without the busy signal, same result.

The first time I noticed this behavior was this past week when there seemed to be some changes with GV/G5 causing one-way audio. I began using GV/sipgate until I could sort out the GV/G5 problem. Sipgate worked flawlessly right off the bat except for some caller ID issues and a slightly longer audio delay (long enough to make calls somewhat painful and bolster my determination in getting GV/G5 working again.) It's during the use of sipgate that I noticed the GVOut one call problem, but I blew it off because I assumed it may be isolated to sipgate, and besides, I had bigger fish to fry.

I have since fixed the GV/G5 one-way audio issue, but the GVOut one call problem has persisted. I them assumed the GVOut problem may be due to the NAT setting changes made in the SPA3102 which were required to fix the GV/G5 issue. But, while GVOut only makes one call then craps out, I can initiate as many calls as I want from the GV web page Call button, even immediately after GVOut has crapped out.

Edit: This issue may have been due to GV growing pains. In any case the latest version of GVOut (version 1.1.5.1 as of this writing) is currently working very well.

doohickey · Post by **doohickey** » Mon Sep 07, 2009 4:16 pm

az1324, is there any chance you would consider releasing the source code? I'm not sure how far I would get with it, I'm not really a Windows guy, but I would certainly use this opportunity to cut my teeth.

What I'm most interested in is making strictly a call initiator for the GV Call feature, as I use the dial plan method.

az1324 · Post by **az1324** » Fri Sep 11, 2009 11:30 am

Here is a small update for GVOut. I'm not even using it anymore in favor of SIPSorcery. Update adds a dial plan mode.

degarb · Post by **degarb** » Thu Sep 17, 2009 12:39 pm

latest version of gvout is crashing on startup on xp pro sp3.

I bought a papt2 from staples.com and not sure if unlocked or not or what that mean or firmware flash. I cannot find the docs on cd. So far after hours and hours only on page 6 reading of this thread. I only get pap2t to work with sipgate, but when I turn on outgoing proxy, like other user, it breaks. If I put outgoing as 192.168.0.10:5060 I can get incoming calls but I cannot dial out.

Now problem is there is no restore facotory default button I can see. Very confusing setup, as promised in reviews; Cisco like complexity for complexity sake. I don't see sipgate screeshots on sipgate site. Unsure of stun setting.

So, alot of questions.

Got sipsorcery account--the preferred way-- but clueless there where to start. They like complexity for complexity sake too.

doohickey · Post by **doohickey** » Thu Sep 17, 2009 3:32 pm

degarb wrote:I bought a papt2 from staples.com and not sure if unlocked or not or what that mean or firmware flash.

I would doubt that Staples sells locked products. You can download firmware, if needed, by following the product information link posted below.

degarb wrote:Now problem is there is no restore facotory default button I can see.

Resetting the factory defaults is done with the phone that is connected to the device through what Cisco calls the Interactive Voice Response Menu, at least that's how it works on my SPA3102. This information can be found in the user guide, which can be downloaded using one of the following links.

Product information for Cisco ATA devices is here.
User guides for Cisco ATA devices is here.

As for why GVOut may be crashing, make sure you're using the very latest version (found on the first post of this thread) and if possible describe what, if anything, happens when it crashes.

degarb · Post by **degarb** » Thu Sep 17, 2009 10:05 pm

I rebooted and crashing stopped. I assume some remnant of old version was stopping up the port.. Is the newer version of gvout work better on pap2t?

I wasn't having luck other than incoming, but tried every combination I could think (thus need for factory restore)

I was only able to get sipsorcery to work once I was pointed to the url below.

http://www.mysipswitch.com/forum/viewto ... c&start=10

doohickey · Post by **doohickey** » Thu Sep 17, 2009 10:48 pm

degarb wrote:Is the newer version of gvout work better on pap2t?

GVOut version 1.1.5.1 has been working well for me. I don't use a PAP2T, I use a SPA3102, but that shouldn't make much of a difference with regards to GVOut.

From your posts, it appears you're trying to use GVOut as a proxy. I've only ever used GVOut in a dial plan mode, but the first few pages of this thread have a lot of info on setting up GVOut as a proxy with a PAP2T.

synchron · Post by **synchron** » Fri Sep 18, 2009 1:47 pm

az1324 wrote:Here is a small update for GVOut. I'm not even using it anymore in favor of SIPSorcery. Update adds a dial plan mode.

For what its worth, you've done a superb job to the MJ community providing these tools! Even though GVOut was a hassle for me, MJMD5 proxy was excellent when it was needed, before, I too, switch to SS once they got GV callback to work with other providers besides cruddy quality Gizmo.

And, go figure, over at DDWRT.com, after over a full year in "WIP", they finally provided a DDWRT capable firmware for my Airlink 101 670W router that I could use to stick your MJMD5 on. But since SS is working so great on both the ATA and my Ipod touch, I'd rather not screw around with my one sacred router............ until SS ever goes down (fingers crossed it won't, anytime soon).

Synchron

anant · Post by **anant** » Tue Sep 22, 2009 3:05 pm

Hi Folks:

I have signed up for Callcentric and I got a phone # 1777xxxyyyy. I am trying to add this phone to my GV accont. But GV not able to verify this callcentric phone #. Have anyone experienced this problem ?

anant

macman4hire · Post by **macman4hire** » Tue Sep 22, 2009 4:09 pm

The Callcentric 1777 number will not work with Google Voice at this time. You could however forward a Gizmo5 number that you have verified in Google Voice to your Callcentric if you have a limited amount of SIP account registrations available in your configuration. This can be done by going to Gizmo5 members login page and selecting the forward tab. Next in the forward box place the following [email protected]. Hope this helps.

anant · Post by **anant** » Tue Sep 22, 2009 4:31 pm

Thanks for your repy.

I have registered callcentric with SS and I have set up a Callcentric dial plan. I want to make outbound calls just like I currently do with gizmo/sipgate etc under SS w/o using computer.
Since I cannot add the callcentric telephone # to GV, like I did with gizmo, sipgate etc, I cannot make outbound calls using callcentric telephone. I realize Callcentric # also is another gizmo telephone in GV account..

mel2000 · Post by **mel2000** » Sat Oct 03, 2009 11:58 am

anant wrote:I have signed up for Callcentric and I got a phone # 1777xxxyyyy. I am trying to add this phone to my GV accont. But GV not able to verify this callcentric phone #.

You need to forward your GV number to your Callcentric local DID number that you purchased, not the 1777 account number. You'll also need to email Callcentric support to have them set your caller ID to your GV number, unless you want your local DID to be used as your caller ID.

JD2 · Post by **JD2** » Tue Oct 13, 2009 9:18 pm

I am running Express Talk 3.1 with the Gizmo5 service and Google Voice. I am trying to use GVOut v1.1.6.0 for the outgoing call functionality. However, if I set GVOut to use the same Listen port as Express Talk, GVOut crashes. If I set it to use a different port (which I don't think I should since isn't GVOut supposed to intercept the Express Talk outgoing call requests?), GVOut doesn't crash, but it also doesn't intercept the Express Talk outgoing calls which are made with Gizmo5's 3-minute limit.

So, does GVOut work with Windows 7 64-bit? If so, what should I set my Listen port to be for GVOut? Any suggestions on the other settings?

JD2 · Post by **JD2** » Tue Oct 13, 2009 11:45 pm

JD2 wrote:So, does GVOut work with Windows 7 64-bit? If so, what should I set my Listen port to be for GVOut? Any suggestions on the other settings?

Okay I will answer these questions myself, since I got it to work.

GVOut does work with Windows 7 64-bit. Since GVOut is a SIP proxy of sorts, its listen port needs to be set to a different UDP port than that of Express Talk (or another SIP client) if GVOut is running on the same PC as Express Talk. Express Talk simply needs to be configured to use GVOut as its outbound server with a setting of localhost:<GVOut's ListenPort> if GVOut is running on the same PC.

kd5eet · Post by **kd5eet** » Thu Nov 26, 2009 11:04 pm

At first GVOUT worked great, but now I keep getting "GVOUT has encountered a problem and has to shut down"

JD2 · Post by **JD2** » Fri Nov 27, 2009 12:09 am

kd5eet wrote:At first GVOUT worked great, but now I keep getting "GVOUT has encountered a problem and has to shut down"

GVOut no longer works for me either. I suspect that Google changed something in its setup when it bought Gizmo5.

az1324 · Post by **az1324** » Sat Nov 28, 2009 1:30 am

Check the newest version guys.

kd5eet · Post by **kd5eet** » Sat Nov 28, 2009 10:24 pm

JD2 wrote:
kd5eet wrote: GVOut no longer works for me either. I suspect that Google changed something in its setup when it bought Gizmo5.
The problem I have is different. For me, it keeps crashing.

JD2 · Post by **JD2** » Sun Nov 29, 2009 12:09 am

az1324 wrote:Check the newest version guys.

I have tried the new version, but the problem remains. I can no longer use GVOut as the outbound server with ExpressTalk 3.1 or 4.02. It previously worked with ExpressTalk v3.1, but stopped after the time when Google announced it had bought Gizmo5, and hasn't worked since.

JD2 · Post by **JD2** » Sun Nov 29, 2009 12:11 am

kd5eet wrote:The problem I have is different. For me, it keeps crashing.

I know your problem is different from mine. For me GVOut only crashed when I set it to use the same port as my telephony software (ExpressTalk). Right now, GVOut doesn't work at all. It never calls back when I try to place a call.

az1324 · Post by **az1324** » Sun Nov 29, 2009 6:01 am

JD2 wrote:
kd5eet wrote:The problem I have is different. For me, it keeps crashing.
I know your problem is different from mine. For me GVOut only crashed when I set it to use the same port as my telephony software (ExpressTalk). Right now, GVOut doesn't work at all. It never calls back when I try to place a call.

Latest version added and tested working with ExpressTalk.

sabresfan · Post by **sabresfan** » Wed Jan 20, 2010 5:27 pm

This is a great tool with MJ and the xlite plugin. I'm using this with sipgate and everything works great thanks az1324.

toddmo · Post by **toddmo** » Sun Jan 24, 2010 11:10 am

az1324,

I'm using this and this is saving me money

Way cool and you are the man!

Sorry if this is a duplicate post;
I couldn't bring myself to read 23 pages.

I'm a .NET programmer,
and it would appear you created GVOut with some .NET language.

Have you posted the source code any where?

My goal:
I would like to learn how all this works,
and maybe someday programmatically make a phone call
and even respond to touch tones.

Can you point me in the right direction?
Thanks in advance!

If I come up with something neato with it,
I'll be happy to share my code from here.

gottkung · Post by **gottkung** » Fri Mar 12, 2010 3:42 pm

hello i need help

i have Gv and G5 number and linksys Pap2
i can get incomecall just fine but
when i try GVOut i don't know how it going to work
i can't out going call i don't know how to get busy signal
could some one help me set up please

and one more question why home phone can't call GV number?
i have try with many people, only cellphone can call GV number?

please help
thank you

degarb · Post by **degarb** » Sun May 23, 2010 3:47 pm

az1324 wrote:Here is a small update for GVOut. I'm not even using it anymore in favor of SIPSorcery. Update adds a dial plan mode.

SS quit working a half a year ago and I have abandoned it. Way too complex and poorly designed since nothing is intelligible, much less works.

I am running mjmd5 in windows tray and pap2t. The issue there is incoming calls immediately kick to voice mail, so no incoming. And on line one I run sipgate.

I would like to get gvout to work. But tried all settings today and no luck. Maybe I need a new version?

sabresfan · Post by **sabresfan** » Sun May 23, 2010 5:11 pm

degarb wrote:
az1324 wrote:Here is a small update for GVOut. I'm not even using it anymore in favor of SIPSorcery. Update adds a dial plan mode.
SS quit working a half a year ago and I have abandoned it. Way too complex and poorly designed since nothing is intelligible, much less works.

I am running mjmd5 in windows tray and pap2t. The issue there is incoming calls immediately kick to voice mail, so no incoming. And on line one I run sipgate.

I would like to get gvout to work. But tried all settings today and no luck. Maybe I need a new version?

Check out this tutorial for SS http://sipsorcery.wordpress.com/2009/08 ... -tutorial/ it makes it very simple to use SS with googlevoice now. It has a very simple dial plan that's easy to understand. On your MJ line check and see what your registration expire is set to 180 or 90 seem to be good values for this.

Darkman90808 · Post by **Darkman90808** » Tue May 25, 2010 11:04 am

sabresfan... one man's "easy to understand" is another man's PITA.

I revisited sipsorcery/Google Voice/sipgate but was never able to get the darn thing working. However, I'm using sipgate by calling out from Google Voice and ringing my sipgate number with great results.

Question: What benefit does the sipsorcery/GV/sipgate combination offer over the other method, which I believe I learned from you?

Thanks...

sabresfan · Post by **sabresfan** » Tue May 25, 2010 11:29 am

Darkman90808 wrote:sabresfan... one man's "easy to understand" is another man's PITA.

I revisited sipsorcery/Google Voice/sipgate but was never able to get the darn thing working. However, I'm using sipgate by calling out from Google Voice and ringing my sipgate number with great results.

Question: What benefit does the sipsorcery/GV/sipgate combination offer over the other method, which I believe I learned from you?

Thanks...

The benefit of using sipsorcery is being able to pickup the phone and dial like normal. All you hear is an additional ring on average. Sipsorcery with the ruby scripts complete the call back to you from googlevoice. It's really the same as using the browser addons for googlevoice but your phone never rings. With the link posted above there is a simple 3 line dial plan for sipsorcery and googlevoice now. The other advantage of sipsorcery is having multiple sip accounts with multiple providers ring one phone. One other advantage is not having to keep a computer on all the time.

Darkman90808 · Post by **Darkman90808** » Tue May 25, 2010 12:15 pm

Thanks for the timely response. It looks like I'm going to have to lock myself in a room and stay there till I get it.

RedPenguin · Post by **RedPenguin** » Sun Jun 06, 2010 8:01 pm

I have two SIP accounts, which one rings to my computer and the other rings to my iPhone when I am on the go.

When I try to use GVOut for the second account, I get it attempting to connect to the SIP on port 5061 as a previous post explained.

I read that a dial plan may work in this case, but I cannot find any dial plan for GVOut that is for X-Lite, all seem to be for other software.

EDIT: Also, when I try to run GVOut on the same PC as X-Lite vs on my XP server, using gvout d, it seems to say

GV Commands Sent
GV Response: OK
GV Signout

but it spit out an enormous amount of HTML code before, and from other posts, I did not see anyone who had this.

N7AS · Post by **N7AS** » Thu Jun 10, 2010 1:29 pm

I have GVOut working with my Linksys/Cisco SPA941 IP Phone. This is a 4 line phone and have GVOut configured on Line 1 for outgoing calls. I put a shortcut in my startup folder so that it loads on windows startup or reboot (Windows 7). I also have a Dell Optiplex running XP Pro which is on 24/7 as I run my radio scanner live feed sending audio and digital tag data streams to radioreference.com. I was thinking of running GVOut on that machine so it would still function if my main PC was not running. All the PC's are on the same network. Well, I tried it and GVOut would not run for some unknown reason. I kept getting some error that was not explained and had to close the program. Does anyone have any idea what's happening and maybe a way to fix it?

.

az1324 · Post by **az1324** » Sat Jun 19, 2010 9:52 pm

make sure you have .NET 3.5 installed?

magicJack and magicJack Plus Support, Reviews, FAQs and Tricks

New Toy: GVOut Google Voice Outgoing Proxy Dialer (Windows)

GVout proxy error help

GVout proxy error help

Callcentric with GoogleVoice

Cannot add Callcentric telephone to GV account.

Re: Callcentric with GoogleVoice

Windows 7 64-bit Support?

Re: Windows 7 64-bit Support?

GVOut no longer works for me.

Re: GVOut no longer works for me.

Still Doesn't Work

Re: GVOut no longer works for me.

Re: GVOut no longer works for me.

Two GVOuts same machine?

GVOut on XP Pro not working...