Ports use for Magicjack
Moderators: Bill Smith, Pilot
Ports use for Magicjack
Can anyone tell me what ports use for Magicjack?
The ports vary with each reboot.
This link well tell you how to find which ports are in use by MJ at any given time -
http://www.phoneservicesupport.com/inco ... 48-15.html
The important part is reproduced below.
------------
PART ONE
------------
1.) In windows click the lower-left START button
2.) ...then click on the ...RUN item ( a pop-up box will pop-up)
3.) at the Open: space type "cmd" (without the quotes)
4.) hit OK (this brings up a DOS command-line terminal...)
---------------
PART TWO
---------------
1.) at the command prompt > type "netstat -an" (without the quotes)
2.) hit the return button
3.) a chart called "Active Connections" will appear
----------------------
PART THREE
----------------------
1.) the first column (reading left-to-right) is PROTO
2.) two types of protocols appear: TCP and UDP
3.) the second column (Local Address) reads: "ip_address:port_number"
4.) look for a line having these 3 values:
1... UDP (that's easy)
2... 127.0.0.1 (that's a little more difficult)
3... a port number between 40,000 and 65,000 (that's tough)
5.) EXAMPLE
UDP 127.0.0.1:58228 *.*
--------------------------
PART FOUR
--------------------------
1.) look for a matching line with the same "UDP, the same port_numeber,
but a different ip_address
UDP 192.168.1.7:58228 *.*
2.) the different ip_number is the ip address of your MagicJack unit
This link well tell you how to find which ports are in use by MJ at any given time -
http://www.phoneservicesupport.com/inco ... 48-15.html
The important part is reproduced below.
------------
PART ONE
------------
1.) In windows click the lower-left START button
2.) ...then click on the ...RUN item ( a pop-up box will pop-up)
3.) at the Open: space type "cmd" (without the quotes)
4.) hit OK (this brings up a DOS command-line terminal...)
---------------
PART TWO
---------------
1.) at the command prompt > type "netstat -an" (without the quotes)
2.) hit the return button
3.) a chart called "Active Connections" will appear
----------------------
PART THREE
----------------------
1.) the first column (reading left-to-right) is PROTO
2.) two types of protocols appear: TCP and UDP
3.) the second column (Local Address) reads: "ip_address:port_number"
4.) look for a line having these 3 values:
1... UDP (that's easy)
2... 127.0.0.1 (that's a little more difficult)
3... a port number between 40,000 and 65,000 (that's tough)
5.) EXAMPLE
UDP 127.0.0.1:58228 *.*
--------------------------
PART FOUR
--------------------------
1.) look for a matching line with the same "UDP, the same port_numeber,
but a different ip_address
UDP 192.168.1.7:58228 *.*
2.) the different ip_number is the ip address of your MagicJack unit
-
marandacar
- MagicJack Newbie
- Posts: 1
- Joined: Tue Jul 09, 2013 12:36 pm
magic jack ports
i have a zhone wireless modem in trinidad. i have gone into the nat and added ports 5060 and 5070. i checked if the ports were open and they are not. (i'm not experienced at doing these things, but i'm trying...lol) i don't know why i'm still getting the message that i'm not connected to internet. i have also tested out all my ethernet cables and they all work.
i tried to find a matching udp and tcp and could not find them in my list when i ran the netstat -an on the cmd. i'm at my wits end!
funny thing is, when i got my dsl, it worked the first day. when i called tstt in trinidad to find out why i was only running at 256 k and not 2 mg, they said they had to configure the modem onto the account. being an ex internet tech i understood because i had to check off a box on cx's accounts as well. since then i have been getting the error 3 and also error 23 at times.
i have powercycled, and waited for 10 seconds and did a restart on my laptop when i added the ports as well.
hopefully i could get more advice?
i tried to find a matching udp and tcp and could not find them in my list when i ran the netstat -an on the cmd. i'm at my wits end!
funny thing is, when i got my dsl, it worked the first day. when i called tstt in trinidad to find out why i was only running at 256 k and not 2 mg, they said they had to configure the modem onto the account. being an ex internet tech i understood because i had to check off a box on cx's accounts as well. since then i have been getting the error 3 and also error 23 at times.
i have powercycled, and waited for 10 seconds and did a restart on my laptop when i added the ports as well.
hopefully i could get more advice?